73-11-01
 ALL  ú ú N02 Page 422 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
b) Install the clamp (3A) with the bolt (4A). c) Tighten the bolt (4A) to 36-40 pound-inches (4.07-4.52 newton-meters).
 9)  ENGINES WITH THE SUPPLY TUBE (3) ATTACHED TO THE HPC BRACKET; Do the steps that follow: a) Lubricate the threads of the bolt (16A), which attaches
 the clamp (15A), with engine oil. b) Install the clamp (15A) with the bolt (16A) and the nut (17A). c) Tighten the nut (17A) to 36-40 pound-inches (4.07-4.52 newton-meters).
 10) Install the clamps on the EEC wire harness to the support bracket: a) Lubricate the threads of the bolt (5) with engine oil. b) Install the clamps on the EEC wire harness to the
 support bracket with the bolt (5). c) Tighten the bolt (5) to 36-40 pound-inches (4.1-4.5 newton-meters).
 CAUTION: USE THE CORRECT ASSEMBLY PROCEDURE, AND TOOLS, FOR
_______ THE HARNESS CONNECTOR INSTALLATION (AMM 70-24-05/201). IF YOU USE THE INCORRECT ASSEMBLY PROCEDURE, OR TOOLS, A DAMAGED OR LOOSE CONNECTOR CAN OCCUR. A LOOSE CONNECTOR PERMITS VIBRATION, WHICH CAUSES THE CONTACTS TO WEAR AND DECREASES THE LIGHTNING PROTECTION.
 11) Connect two electrical connectors, W5P1 and W4P2 (7 and 7A), to the FMU (6) (AMM 70-24-05/201): a) Remove the caps from the electrical connectors (7 and
 7A). b) Connect two electrical connectors (7 and 7A) to the FMU (6).
 (g)  If the fuel pump (11) was installed without the FMU (6), install the fuel metering unit (AMM 73-21-01/401).
 (h) Install the drain tube (28), the oil-cooler-outlet fuel hose (36) and the oil-cooler-inlet fuel tube (34): 1) Lubricate the threads of the bolts (40 and 43) with engine oil. 2) Connect the drain tube (28) for the fuel pump (11) to the elbow (29). a) Tighten the elbow (29) and the tube nut.
 3)  Install the oil-cooler-outlet fuel hose (36) to the fuel pump port (11).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-01
 ALL  ú ú N02 Page 423 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
4)  Install the oil-cooler-outlet fuel hose (36) to the fuel
 pump (11) with the bolts (43).

 5)  Install the oil-cooler-inlet fuel tube (34) to the fuel
 pump (11) with the bolts (40).

 6)  Tighten the bolts (40 and 43) to 85-95 pound-inches
 (9.6-10.7 newton-meters).

 (i)  
ENGINES PRE-PW-SB 73-161; Tighten the bolts (51) which attach the bracket (63) and the differential pressure switch S1585 (50) for the fuel filter:

 (j)  
ENGINES POST-PW-SB 73-161; Tighten the bolts (51) which attach the bracket (79) and the differential pressure switch S1585 (50) for the fuel filter: 1) Tighten the bolts (51) to 85-95 pound-inches (9.6-10.7

 newton-meters).

 (k)  
Connect the electrical connector DS1585 (1) to the differential pressure switch S1585 (52) for the fuel filter: 1) Remove the cap from the electrical connector DS1585 (1). 2) Connect the electrical connector DS1585 to the differential

 pressure switch S1585 (52).

 (l)  
ENGINES PRE-PW-SB 73-161; Connect the EEC wire harness to the thermocouple probe (67): 1) Install the lugs (44) for the EEC wire harness to the

 studs (67) and loosely install the nuts (64 and 65) and
 washers (66 and 70).
 2) Loosely install the clamp, ground strap and bolt to the
 bracket on the housing.

 CAUTION: MAKE SURE THE THERMOCOUPLE STUD BOX DOES NOT TURN
_______
 WHEN THE COUPLING NUT IS TIGHTENED. IF THE
 THERMOCOUPLE STUD BOX TURNS, DAMAGE TO THE WIRE
 HARNESS CAN OCCUR.

 3)  While you hold the thermocouple stud box, tighten the
 coupling nut on the thermocouple probe (67) to 95-100
 pound-inches (10.734-11.298 newton-meters).

 CAUTION: DO NOT ALIGN THE THERMOCOUPLE STUD BOX AFTER THE
_______
 COUPLING NUT IS TIGHTENED. HOLD THE THERMOCOUPLE
 STUD BOX AND LOOSEN THE COUPLING NUT TO ALIGN THE
 THERMOCOUPLE STUD BOX AGAIN.

 4)  Make sure the thermocouple stud box is aligned.
 CAUTION: TOO MUCH TORQUE (MORE THAN THE MAXIMUM TORQUE) ON THE
_______
 THERMOCOUPLE PROBE NUTS CAN LOOSEN OR DAMAGE THE
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機燃油和控制 1(27)