(b)
ENGINES PRE-PW-SB 73-106; If you will remove the No. 20 fuel injector, remove the bolt (65) and nut (64) which attach the tube clamp (63) on the PT4.95 sense tube to the bracket (9).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-05
ALL ú ú N01 Page 440 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(c) (d) ENGINES POST-PW-SB 73-106; If you will remove the No. 20 fuel injector, remove the bolt (65) which attaches the tube clamp (63) on the PT4.95 sense tube to the bracket (9).If you will remove the No. 21 fuel injector, do the steps that follow:
(e) (f) (g) (h) (i) (j) 1) Remove the bolts (68, 77) and washers (67, 76) which attach the tube clamps (66, 75) on the pneumatic tube. 2) Remove the screws (70, 80) and washers (69, 79) which attach the ground straps (71, 78). 3) Remove the bolt (73) and nut (74) which attach the tube clamp (72) on the air vent for the diffuser seal to the bracket (8).Put the container below the fuel manifold (4).Disconnect the supply tube (1) from the fuel manifold (4).Disconnect the fuel manifold (4) from all three fuel injectors (5).Remove the fuel manifold (4) from the engine. 1) Install caps on the openings of the fuel manifold (4). 2) Discard the packings (20).Remove the transfer tube (2) from the supply tube (1). 1) Discard the packings (3) from the transfer tube (2).For the No. 20 fuel injector, remove the bolts (21) which attach the fuel injector (5) and the bracket (9) to the diffuser and combustor case.
(k) For the No. 21 fuel injector, remove the bolts (21) which attach the fuel injector (5) and the brackets (7, 8) to the diffuser and combustor case.
(l) Remove the fuel injector (5), the applicable brackets (7 or 8 and 9) and the gasket (19) from the engine.
NOTE:____ Turn or lift the fuel injector, as it is necessary, to disengage the fuel injector from the diffuser and combustor case.
1) Discard the gasket (19).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-05
ALL ú ú N02 Page 441 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(m) Install caps on the open end of the supply tube (1) and the opening in the diffuser and combustor case.
TASK 73-11-05-004-119-N00
9. Remove the No. 22, 23, or 24 Fuel Injector and Support (Fig. 401 and 405)______________________________________________________
A. Standard Tools and Equipment
(1)
Container - 1 quart (1 liter) capacity, used to collect the fuel
B.
References
(1)
AMM 71-11-04/201, Fan Cowl Panels
(2)
AMM 71-11-06/201, Core Cowl Panels
(3)
AMM 78-31-00/201, Thrust Reverser System
C.
Access
(1)
Location Zone 412 Engine 1 - Diffuser and Combustor Case 11 o'clock 422 Engine 2 - Diffuser and Combustor Case 11 o'clock 432 Engine 3 - Diffuser and Combustor Case 11 o'clock 442 Engine 4 - Diffuser and Combustor Case 11 o'clock
(2)
Access Panel
415 Left Thrust Reverser Half - Engine 1
425 Left Thrust Reverser Half - Engine 2
435 Left Thrust Reverser Half - Engine 3
445 Left Thrust Reverser Half - Engine 4
D.
Prepare to Remove the No. 22, 23 or 24 Fuel Injector and Support
S 864-120-N00
(1) Make sure the applicable FUEL CONTROL switch is in the CUTOFF position.
S 864-121-N00
WARNING: MAKE SURE YOU OPEN THE CIRCUIT BREAKERS FOR THE ENGINE IGNITION
_______ BEFORE YOU OPEN THE FUEL CONT VALVE. THE IGNITER PLUGS WILL AUTOMATICALLY FIRE IF YOU ARE OUT OF ZERO DETENT, NACELLE ANTI-ICE IS ON, CON IGNITION SWITCH IS SET TO "ON", OR ENGINE START SWITCH IS PULLED TO "ON". IF THE COMBUSTION CHAMBER HAS FUEL IN IT, AN INTERNAL ENGINE OR A TAILPIPE FIRE CAN OCCUR. THE FIRE CAN CAUSE INJURY TO PERSONS OR DAMAGE TO THE ENGINE.
(2)
For the applicable engine, open these circuit breakers and install the DO-NOT-CLOSE tags:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機燃油和控制 1(59)
