S 085-023-N00

 (8)  
Remove the load-test-adapter-tool from the pressure relief door.

 (a)  
Remove the pivot support assembly (5) from the cowl structure.

 (b)  
Remove the adapter assembly (2) from the pressure relief door.

 (c)  
Install the mounting bolts, washers and nuts (3) on the latch, and tighten the nuts (3).

 S 725-024-N00
 (9)  
If there is more than one latch on the pressure relief door, do these steps again to do a test of the other latch.

 S 415-025-N00

 (10)
 When you have completed the tests for all the latches on the pressure relief door, do these steps:

 (a)  
Put the blade of a straight-slot screwdriver into the slot of one of the latches (1) on the pressure relief door.

 (b)  
Move the screwdriver handle until the latch (1) is in the fully open position, and close the pressure relief door.

 (c)  
Move the screwdriver in the opposite direction to lock the latch (1).

 (d)  
If there is more than one latch on the pressure relief door, do these steps again to close the opposite latch (1).

 S 445-026-N00
 (11) If it is necessary, do this procedure:  Thrust Reverser Activation After Ground Maintenance (AMM 78-31-00/201).
 TASK 71-11-08-825-005-N00
 3. Cowl Panel Pressure Relief Door Adjustment
__________________________________________
 A. Consumable Materials
 (1)  
C00259 - Primer, BMS 10-11, Type 1

 B.
References

 (1)  
AMM 78-31-00/201, Thrust Reverser System

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-08
 ALL  ú ú N01 Page 507 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
C. Access
 (1)  
Location Zone
 413 and 414 Fan Cowl Panel - Engine 1
 423 and 424 Fan Cowl Panel - Engine 2
 433 and 434 Fan Cowl Panel - Engine 3
 443 and 444 Fan Cowl Panel - Engine 4
 417 and 418 Core Cowl Panel - Engine 1
 427 and 428 Core Cowl Panel - Engine 2
 437 and 438 Core Cowl Panel - Engine 3
 447 and 448 Core Cowl Panel - Engine 4

 D.
Procedure (Fig. 501)

 S 045-010-N00
 WARNING: DO THE THRUST REVERSER DEACTIVATION PROCEDURE TO PREVENT THE
_______ OPERATION OF THE THRUST REVERSER. THE ACCIDENTAL OPERATION OF THE THRUST REVERSER CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  
Do this procedure: Thrust Reverser Deactivation for Ground Maintenance (AMM 78-31-00/201).

 S 825-006-N00

 (2)  
Do a check of adjustment for the pressure relief door.

 (a)  
Make sure that the upper and lower side clearances of the pressure relief doors are 0.03-0.09 inch (0.74-2.26 mm). 1) If the clearance does not agree with the given tolerance,

 remove or install washers between the hinge assemblies and bushings.

 (b)  
Make sure that the forward and aft side clearances of the pressure relief doors are 0.03-0.09 inch (0.74-2.26 mm). 1) If the clearance does not agree with the given tolerance,

 do these steps: a) Use a drift to remove the roll pins from the hinge assemblies.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-08
 ALL  ú ú N01 Page 508 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
b) Loosen the bolts which hold the pressure relief door to
 the hinge assemblies.
 c) Adjust the pressure relief door to agree with the given
 tolerances.
 d) Tighten the bolts.
 e) Find the spare holes in the hinge assemblies opposite
 the holes used for the roll pins before.
 f) Drill the spare holes with a 0.062-0.065 inch (1.5-1.6
 mm) diameter bit.
 g) Install the roll pins in the new holes.
 h) Align the roll pins with the outer side of the pressure
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 動力裝置 POWER PLANT 2(88)