(b)  
Hold the gearbox lock with the bolts and washers removed with the starter QAD adapter. The countersunk face must be adjacent to the bolt head. 1) Tighten the bolts to 260-320 pound-inches (29.2-36.2

 newton-meters).

 (c)  
Install the coverplate on the open end of the start duct.

 (d)  
Hold the coverplate with the V-band clamp removed with the start valve.

 S 492-041-N00
 (10) Install a retaining fixture on the 2.5 bleed valve actuator (referred to as the actuator) (Fig. 202).
 (a)  Loosen the fuel supply and return tubes for the servo valve at the actuator.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-30
 ALL  ú ú N01 Page 210 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
GEARBOX (6 LOCATIONS) LOCK BOLT
WASHER (6 LOCATIONS)SEE B SEE A
FWD 
MAIN GEARBOX  STARTER DRIVE PAD 
A 

COVERPLATE 
SEE  C 
FWD  B  START DUCT 
START DUCT  C  V-BAND CLAMP 
Gearbox Lock Installation Figure 201 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-30
 ALL  ú ú N01 Page 211 ú Jun 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES /MAINTENANCE MANUAL ////////////////////////
SERVO FUEL SUPPLY TUBE
SEE A AND B  INTERMEDIATE CASE
SERVO FUEL 
2.5 BLEED ACTUATOR  RETURN TUBE 
HOLDING FIXTURE 
2.5 BLEED 
VALVE ACTUATOR 
A  FWD 
CLAMP 
LOCKWASHER 
(2 LOCATIONS) 
BOLT 
(2 LOCATIONS) 
LOCKNUT 
CLEVIS ROD 
2.5 BLEED 
VALVE ACTUATOR 
B 

2.5 Bleed Actuator Holding Fixture Installation
Figure 202

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-30
 ALL  ú ú N01 Page 212 ú Jun 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(b)  
Put the retaining fixture on the actuator. The holes in the retaining fixture must be aligned with the holes in the actuator.

 (c)  
Hold the retaining fixture to the actuator with the bolts and lockwashers from the retaining fixture.

 (d)  
Tighten the clamp to push against the actuator clevis rod. Continue to tighten the clamp until the 2.5 bleed valve is closed.

 (e)  
Tighten the locknut to lock the clamp.

 (f)  
Tighten the fuel supply and return tubes for the servo valve at the actuator.

 S 492-042-N00
 (11) Put the mats in the inlet cowl.
 S 022-043-N00
 CAUTION: DO NOT USE A STRAP TO ATTACH THE FAN BLADES TO THE GUIDE VANES
_______ AT THE FAN EXIT. DAMAGE TO THE ENGINE CAN OCCUR.
 (12)
 Remove the 1st-stage (fan) blades (AMM 72-31-02/401).

 S 492-044-N00

 (13)
 Install the blade lock.

 S 422-117-N00

 (14)
 Install the locking closure (Fig. 203).

 (a)  
Remove 12 bolts which hold the fan exit fairing to the fan exit case.

 (b)  
Put the locking closure on the fan rotor hub.

 (c)  
Align the eight lugs at the front of the locking closure with the eight blade slots in the front hub.

 (d)  
Align the bolt holes in the locking closure straps with the bolt holes in the fan exit fairing.

 (e)  
Hold the locking closure straps to the fan exit fairing with the bolts given with the locking closure.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 動力裝置 POWER PLANT 2(44)