曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (4)  S 974-020Measure the door when it is closed to make sure it aligns with the fuselage. (a) The door trailing edge must align |0.060 inch (|1.52 mm) of the inlet lip.
 (5)  S 824-035If it is necessary, adjust the door: (a) Loosen the locknuts (20 and 21) on the bottom of the actuator (3). (b) Turn the adjustment nut (22) to align the door to |0.060 inch (|1.52 mm) of the inlet lip. (c) Tighten the locknuts (20 and 21) on the bottom of the actuator (3).
 (6)  S 714-021Do a check of the actuator (3) operation:
 (a)  Energize the actuator (3) and do a check of the operation in the two directions.
 (7)  S 914-022Install lockwires on the locknuts (20 and 21) on the actuator (3).
 (8)  S 824-028Adjust the position switch for the air inlet door (Ref 49-15-05/201).
 (9)  S 714-036Do a check of the installation and the operation of the air inlet door (Ref 49-15-03/601).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-15-04
 ALL  ú ú 01 Page 407 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 414-023
 (10)
 Close the APU access doors:

 (a)  
Do a visual check of the EGT bus bars:
 1) Make sure the bus bars are not damaged.
 2) Make sure no metal parts touch the bus bars.
 3) Make sure the bus bars do not touch each other.

 (b)  
Disengage the support rods for the APU access doors.

 (c)  
Put the support rods in the clips on the inner side of the APU access doors.

 (d)  
Make sure the insulation covers correctly attach to the APU compartment firewall.

 (e)  
Close the APU access doors.

 (f)  
Close the latches on the APU access doors.

 S 864-024
 (11)
 Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P83 Panel, E8 Aft Equipment Center
 1) APU PRIMARY CONT

 (b)  
P6 Main Power Supply Panel
 1) 6K18 APU ALTN CONT

 

 S 864-025
 (12) Remove the DO-NOT-OPERATE tag from the APU control switch on the P5 panel.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-15-04
 ALL  ú ú 03 Page 408 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 APU DOOR POSITION SWITCH - MAINTENANCE PRACTICES
________________________________________________
 1.  General_______
 A.  This procedure contains these three tasks:
 (1)  
Door Position Switch Removal

 (2)  
Door Position Switch Installation

 (3)  
Door Position Switch Adjustment.

 B.  
The door position switch is on the forward, lower side of the air inlet duct. The switch is above the inlet door actuator.

 C.  
You can get access to the door position switch through the APU access doors at the top of the APU compartment.

 TASK 49-15-05-002-001
 2.  Door Position Switch Removal (Fig. 201)____________________________
 A.  References
 (1)  
WDM 49-15-11

 (2)  
SSM 49-11-01, 49-15-01

 (3)  
IPC 49-15-51 Fig. 1

 B.  
Access

 (1)  
Location Zone

 318AR  APU Compartment-Forward Side of Air Inlet Plenum Above Actuator Container, RH

 (2)  
Access Panel
 317AL APU Access Door
 318AR APU Access Door

 C.  
Procedure

 S 862-002
 (1)  
Make sure the APU control switch on the P5 panel is OFF and attach a DO-NOT-OPERATE tag.

 S 862-003

 (2)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6 Main Power Supply Panel
 1) 6K18 APU ALTN CONT

 (b)  
P83 Panel, E8 Aft Equipment Center
 1) APU PRIMARY CONT

 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 1(123)