S 862-022
(3)
Put the subsequent items in the CMC scratchpad with Input
Monitoring:
PORT____ LABEL_____ SDI
E 099 270 00 E 099 271 00 E 099 272 00 E 099 273 00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-30
ALL ú ú 01 Page 206 ú Feb 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 722-023
(4) Do a test of the nose gear door warning sensors with the CMC:
WARNING: MAKE SURE THAT THE DOOR WILL NOT HIT PERSONS OR EQUIPMENT
_______ WHEN IT OPENS OR CLOSES. FAST MOVEMENT OF THE DOORS CAN CAUSE INJURY TO PERSONS OR CAUSE DAMAGE TO THE EQUIPMENT.
(a) Move the ground release handle for the nose gear doors to the "Doors Open" position. 1) Attach an actuator to the primary door warning sensor
(S406). 2) Make sure that bit 26 of Label 270/Sdi 00 is a 0 (NOT OPEN). 3) Remove the actuator from the primary door warning sensor
(S406). 4) Make sure that Bit 26 of Label 270/Sdi 00 is a 1 (OPEN). 5) Attach an actuator to the alternate door warning sensor
(S425). 6) Make sure that bit 26 of Label 272/Sdi 00 is a 0 (NOT OPEN). 7) Remove the actuator from the alternate door warning sensor (S425). 8) Make sure that Bit 26 of Label 272/Sdi 00 is a 1 (OPEN).
H. Put the Airplane Back to Its Usual Condition
S 862-026
(1) Move the landing gear lever to the DN position.
S 862-025
WARNING: MAKE SURE THAT ALL PERSONS AND EQUIPMENT ARE CLEAR OF DOOR
_______ OPERATION PATH. FAST MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
(2)
Move the ground release handle for the nose gear door to the STOWED position.
(3)
Move the landing gear lever to the OFF position.
S 862-020
(4)
Remove the electrical power, if it is not necessary
(Ref 24-22-00/201).
S 862-027
(5)
Remove hydraulic pressure, if it is not necessary
(Ref 29-11-00/201).
S 862-024
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-30
ALL ú ú 01 Page 207 ú Feb 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
BODY LANDING GEAR DOOR WARNING SENSOR - MAINTENANCE PRACTICES
_____________________________________________________________
1. General
_______
A. This section has these two tasks:
-Removal of the body landing gear door warning sensor
-
Installation of the body landing gear door warning sensor.
B.
The door warning sensors for the body gear are at the bottom of the door stop support beam. The support beam is at the forward edge of the body gear doors.
C.
The procedure to remove and install the primary or the alternate sensors is the same.
TASK 32-61-31-002-001
2. Remove the Door Warning Sensors for the Body Landing Gear
_________________________________________________________
A. Standard Tools and Equipment
(1)
Plastic scraper that is nonabrasive or conductive
B.
References
(1)
09-11-00/201, Towing
(2)
AMM 32-00-30/201, Landing Gear Door Locks
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 起落架 LANDING GEAR 9(113)
