32-61-21
 ALL  ú ú 02 Page 214 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WING GEAR TRUCK TILT SENSOR - MAINTENANCE PRACTICES
___________________________________________________
 1.  General
_______
 A.  The primary and alternate sensors are installed on a support bracket on the upper torsion link. Each primary (S417 LH, S416 RH) and alternate (S615, LH, S614 RH) sensor pair is installed on one support bracket. The brackets are installed on the upper torsion link.
 B.  When you replace the sensor, it is usually not necessary to adjust the clearance between the sensor and target unless the sensor or target is damaged.
 C.  This subject has these tasks:
 (1)  
Removal of the truck tilt sensor for the wing gear

 (2)  
Installation of the truck tilt sensor for the wing gear

 (3)  
Removal of the truck tilt sensor target bracket for the wing gear

 (4)  
Installation of the truck tilt sensor target bracket for the wing gear

 (5)  
Adjustment of the truck tilt sensor for the wing gear

 (6)  
Test of the truck tilt sensor for the wing gear

 TASK 32-61-22-002-026
 2.  Removal of the Truck Tilt Sensor for the Wing Gear
__________________________________________________
 A.  Standard Tools
 (1)  
Nonabrasive, nonconducting plastic scraper

 B.  
References

 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 32-09-02/201, Air/Ground Relay System

 (3)  
AMM 32-00-30/201, Landing Gear Door Locks

 (4)  
AIPC 32-61-57 Fig. 21

 C.  
Access

 (1)  
Location Zone
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH

 D.  
Prepare for Removal

 S 492-027
 WARNING: YOU MUST CAREFULLY INSTALL GROUND LOCKS IN ALL LANDING GEAR.
_______ AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  Make sure that ground locks are installed on all landing gear (AMM 09-11-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-61-22
 ALL  ú ú 01 Page 201 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 492-003
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  Install the door locks for the main gear (AMM 32-00-30/201).
 S 862-004
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO PREPARE
_______ THE SAFETY SENSITIVE SYSTEMS FOR THE AIR MODE. FAILURE TO DO THE STEPS CORRECTLY CAN CAUSE THE AUTOMATIC OPERATION OF AIRPLANE SYSTEMS. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (3)  
Prepare the airplane for the air mode (AMM 32-09-02/201).

 S 862-005

 (4)  
For removal of the alternate sensor, open this circuit breaker on the P7 Overhead Circuit Breaker Panel and install a DO-NOT-CLOSE tag:

 (a)  
7F23, LANDING GEAR DSP & CONT ALTN

 S 862-006
 (5)  
For removal of the primary sensor, open this circuit breaker on the P7 Overhead Circuit Breaker Panel and install a DO-NOT-CLOSE tag:

 (a)  
7F22, LANDING GEAR DSP & CONT PRI

 E.
Remove the Truck Tilt Sensor (Fig. 201)

 S 032-028
 (1)  
Do these steps to disconnect the sensor wires:

 (a)  
Remove the cover from the junction box installed near the sensor.

 NOTE: The junction box is near the sensor switch on the
____ upper torsion link of the wing gear.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-61-22
 ALL  ú ú 01 Page 202 ú Feb 18/00
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 9(103)