SHOCK STRUT 
LINK UPPER TORSION 
SEE  A 
A  SCREW 
SENSOR CONDUIT 
FWD 
FWD  0.10 |0.015 INCH TARGETS  A 
1  LEFT WING RIGHT WING LANDING GEAR  SENSOR S417 S615 S416 S614  PRI/ALT ALTERNATE PRIMARY ALTERNATE PRIMARY  LOCATION OUTBOARD INBOARD OUTBOARD INBOARD  SIDE VIEW A 

PRIMARY ALTERNATE
SENSOR
SENSOR
1

1
INBD
LEFT WING GEAR TRUCK TILT SENSOR SHOWN (RIGHT WING GEAR TRUCK TILT SENSOR SIMILAR) A-A
Wing Gear Truck Tilt Sensor Installation
Figure 201

E00437
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-61-22
 ALL  ú ú 03 Page 203 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Remove the sealant material from the electrical terminals with the plastic scraper.

 (c)  
Make a note of the terminal location and the wire color for the sensor installation.

 (d)  
Remove the sensor wires from the terminal strip.

 (e)  
Carefully remove the terminal lugs from the sensor leads.

 (f)  
Attach a line that is longer than the conduit to the sensor wires.

 NOTE: You will use this line to pull the sensor wires through
____ the conduit, during the installation.
 S 022-007
 (2)  
Do these steps to remove the sensor:

 (a)  
Remove the conduit nut.

 (b)  
Remove the sensor mounting screws.

 (c)  
Carefully pull the electrical leads from the conduit.

 NOTE: Do not pull the line fully out of the conduit.
____
 TASK 32-61-22-402-008
 3. Installation of the Truck Tilt Sensor for the Wing Gear
_______________________________________________________
 A. Consumable Materials
 (1)  
A00704 Sealant - Silicone, RTV 162

 (2)  
B00083 Solvent - Aliphatic Naphtha, TT-N-95, Type 2

 (3)  
C00582 Primer - SS-4004

 B.
References

 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 32-00-30/201, Landing Gear Door Locks

 (3)  
AMM 32-09-02/201, Air/Ground Relay System

 (4)  
AMM 32-09-03/501, Proximity Switch Electronics Unit

 (5)  
AIPC 32-61-57 Fig. 21

 C.
Access

 (1)  
Location Zone
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH

 D.
Install the Truck Tilt Sensor (Fig. 201)

 S 422-009
 (1)  
Do these steps to install the sensor:

 (a)  
Twist the sensor leads together and attach the line that you kept in the conduit during the removal.

 (b)  
Carefully pull the leads through the conduit and remove the line from the leads.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-61-22
 ALL  ú ú 04 Page 204 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (c)  Install the sensor with the mounting screws.
 NOTE:____ If the sensor or target bracket, or shims have not been damaged or removed, then no sensor adjustment is necessary. However, if the bracket or shims have been damaged or replaced, the sensor clearance must be checked and adjusted (Refer to the task to Adjust the Wing Gear Truck Tilt Sensor).
 1)  Adjust the sensor clearance if it is necessary (Refer to the task to Adjust the Wing Gear Truck Tilt Sensor).
 (2)  S 432-029Connect the sensor wires to the terminal strip: (a) Cut sensor wires to the correct length and install new terminal lugs on the wires. (b) Connect the sensor wires to the terminal strip. (c) Do a check of the terminals and the wire color for the correct connection.
 (3)  S 862-047Remove the DO-NOT-CLOSE tag and close the applicable circuit breaker on the P7 Overhead Circuit Breaker Panel: (a) 7F22, LANDING GEAR DSP & CONT PRI (b) 7F23, LANDING GEAR DSP & CONT ALTN
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 9(104)