27-68-01
ALL ú ú 01 Page 401 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
A INNER RIG PIN HOLE
SCREW CLAMPING SHAFT
ASEE THUMBNUT CONTROL ROD ROD A BSEE CONTROL
B
50`
CRANK CRANK
MARK INDEX BRACKET
BRACKET
MOUNTING
OUTER RIG BRACKET
PIN HOLE
RIG PIN SLOT
BONDING JUMPER
TRANSMITTER BRACKET
TRANSMITTER CLAMPING SCREWS
A
40`
INDEX MARK
SPOILER NO. 4 SPOILER NO. 12A-A
Spoiler Position Transmitter Installation
Figure 401
ELECTRICAL CONNECTOR
INDEX
MARKS
SPOILER POSITION TRANSMITTER
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-68-01
ALL ú ú 01 Page 402 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 864-013
(3)
Do this task: "Trailing Edge Flap Deactivation" (AMM 27-51-00/201).
S 864-004
(4)
Set all FLT CONTROL HYD POWER WING switches on the P461, Pilots' Overhead Maintenance Panel to SHUTOFF.
(a)
Make sure that the four VALVE CLOSED lights come on.
S 864-005
(5)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P180, DC Power Distribution Panel
1) 180H7, LATERAL CONT VLV SYS 1
2) 180E6, LATERAL CONT VLV SYS 2
3) 180H22, LATERAL CONT VLV SYS 3
4) 180E21, LATERAL CONT VLV SYS 4
(b)
P6, Main Power Distribution Panel
1) 6J21, SPLR/ALRN IND
2) 6J20, SPLR/ALRN SENSOR
S 014-006
(6)
Get access to the applicable transmitter.
S 034-007
(7)
Disconnect the electrical connector from the position transmitter: DT435 No. 4 Spoiler Transmitter DT436 No. 12 Spoiler Transmitter
S 034-008
(8)
Disconnect the bonding jumper from the transmitter.
S 024-009
(9)
Remove the transmitter assembly:
(a)
Remove the nut, washer, and screw that attach the control rod to the crank.
(b)
Remove two screws, washers, and nuts that attach the transmitter bracket to the bracket on the wing rear spar.
(c)
Remove the transmitter, the bracket, and the crank assembly from the airplane.
S 034-027
(10)
Disassemble the transmitter assembly:
(a)
Remove the crank from the transmitter shaft.
1) Remove the shaft clamping screw from the crank.
2) Remove the crank.
(b)
Remove the transmitter from the bracket.
1) Loosen the transmitter clamping screws.
2) Remove the inner clamping screw.
3) Remove the transmitter from the bracket.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-68-01
ALL ú ú 01 Page 403 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
TASK 27-68-01-404-010
3. Spoiler Position Transmitter Installation (Fig. 401)_________________________________________
A. Special Tools and Equipment
(1)
M25093-4C rig pin or equivalent diameter rod (0.309-0.311)
B.
Standard Tools and Equipment
(1)
Milliohmmeter - 0 to 0.1 ohms range
C.
References
(1)
AMM 24-22-00/201, Manual Control
(2)
AMM 27-51-00/201, Trailing Edge Flap System
(3)
AIPC 27-68-01, Fig. 1
(4)
SSM 27-68-01
(5)
WDM 27-68-11
D.
Access
(1)
Location Zone
582 No. 4 Spoiler
685 No. 12 Spoiler
E.
Install the Spoiler Position Transmitter
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 7(33)
