(2)  
FREIGHTER AIRPLANES;

 (3)  
AMM 25-59-01/401, Main Deck Compartment Cargo Lining Panel

 (4)  
AMM 29-11-00/201, Main Hydraulic Supply System

 C.
Access

 (1)  
Location Zone
 211, 212 Passenger Cabin - Nose to First Door

 D.
Procedure

 S 424-020
 (1)  
Install the actuator (Fig. 401):

 (a)  
Connect the actuator (4) to the support bracket with the bolt (1), washer (2), and nut (3).

 (b)  
Put the bushing (6) in the piston rod end of the actuator.

 (c)  
Attach the actuator to the idler assembly with the bolt (5), washer (7) and nut (8).

 S 434-012
 (2)  
Connect the electrical connector DX432 to the actuator.

 S 864-013

 (3)
Do this task: "Supply Electrical Power" (AMM 24-22-00/201).

 S 864-014

 (4)
Do this task: "Pressurize Hydraulic System" (AMM 29-11-00/201).

 S 824-015

 (5)  
Adjust the actuator:

 (a)  
Remove the DO-NOT-CLOSE tag and close the following circuit breaker: 1) P7, Overhead Circuit Breaker Panel

 a) 7G6, SPEED BRAKE AUTO CONT

 (b)  
Put the thrust levers No. 1 and No. 3 to a position of less than 15 degrees.

 (c)  
Put the speed brake lever in the ARMED position.

 (d)  
Make sure the actuator moves to the fully extended position.

 (e)  
Open the following circuit breaker and attach a DO-NOT-CLOSE tag: 1) P7, Overhead Circuit Breaker Panel

 a) 7G6, SPEED BRAKE AUTO CONT
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-07
 ALL  ú ú 06 Page 404 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (f)  Put the speed brake lever in the DN position. 1) Make sure the actuator stays fully extended.
 CAUTION:_______ DO NOT ADJUST THE ACTUATOR PISTON ROD. RETRACT DIMENSIONS ARE SET. THE EXTEND AND
 (g) (h)  Measure the clearance between the manual and actuator input assembly (Section A-A) 1) Make sure the clearance is 0.03 to 0.06 inch (.76-1.52mm). 2) If the clearance is not in the tolerance, adjust the length of the actuator control rod.Remove the DO-NOT-CLOSE tag and close the following circuit breakers: 1) P7, Overhead Circuit Breaker Panel a) 7G6, SPEED BRAKE AUTO CONT
 (6)  S 414-023Install the ceiling panels that were removed (AMM 25-59-01/401).
 (7)  S 864-018Do this task: "Hydraulic System Depressurization" (AMM 29-11-00/201).
 (8)  S 864-017Do this task:  "Remove Electrical Power" (AMM 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-07
 ALL  ú ú 04 Page 405 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 SPEED BRAKE CONTROL LEVER LOCK - REMOVAL/INSTALLATION
_____________________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is a task for the removal and a task for the installation of the speed brake control lever lock.
 (1)  
The removal procedure has these parts:

 (a)  
The removal of a ceiling panel

 (b)  
The removal of the electrical wires

 (c)  
The removal of the control lever lock.

 (2)  
The installation procedure has these parts:

 (a)  
The installation of the control lever lock

 (b)  
The installation of the electrical wires

 (c)  
A test of the control lever lock

 (d)  
The installation of the ceiling panel

 TASK 27-62-08-004-001
 2.  Speed Brake Control Lever Lock Removal (Fig. 401)______________________________________
 A.  Special Tools and Equipment
 (1)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 7(20)