曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 position.
 (e) Make sure the speed brake lever is automatically released from
 the DOWN position and moves to the full UP position.
 (f) Put the reverse thrust lever No. 2 in the FORWARD IDLE
 position.
 (g) Put the speed brake lever in the DOWN position.
 (h) Put the reverse thrust lever No. 4 in the reverse thrust
 position.
 (i) Make sure the speed brake lever is automatically released from
 the DOWN position and moves to the full UP position.
 (j) Put the reverse thrust lever No. 4 in the FORWARD IDLE
 position.
 (k) Put the speed brake lever in the DOWN position.
 S 864-011
 (8)  Do this task: "Remove Electrical Power" (AMM 24-22-00/201).
 S 864-020
 (9)  Do this task "Remove Hydraulic Power" (AMM 29-11-00/201).
 S 414-012

 (10)
 Install the left cover assembly on the control stand.

 S 864-015

 (11)
 Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P414, Power Distribution Center - Left 1) 414D8, CAPT PWR SEAT

 (b)  
P415, Power Distribution Center - Right 1) 415H32, F/O POWER SEAT

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-09
 ALL  ú ú 03 Page 406 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 AUTOMATIC SPEED BRAKE ARM SWITCH - REMOVAL/INSTALLATION
_______________________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is a task for the removal and a task for the installation of the automatic speed brake arm switch S217.
 (1)  
The removal procedure has these parts:

 (a)  
The retraction of the automatic speed brake actuator

 (b)  
The removal of the ceiling panel

 (c)  
The removal of the wires from the switch

 (d)  
The removal of the switch

 (2)  
The installation procedure has these parts:

 (a)  
The installation of the switch

 (b)  
The installation of the wires on the switch

 (c)  
An adjustment of the switch

 (d)  
An operational test of the switch

 (e)  
The installation of the ceiling panel.

 B.  
The WDM and SSM refer to the automatic speed brake arm switch as the Spoiler Handle Position Switch S217.

 TASK 27-62-10-004-001
 2.  Automatic Speed Brake Arm Switch Removal (Fig. 401)________________________________________
 A.  References
 (1)  
AMM 25-59-01/401, Main Deck Compartment Cargo Lining Panel

 (2)  
AIPC 27-62-55, Fig. 1

 (3)  
WDM 27-62-11

 (4)  
SSM 27-62-01

 B.  
Access

 (1)  
Location Zone 211, 212 Passenger Cabin - Nose to First Door

 C.  
Procedure

 S 864-002
 (1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P7, Overhead Circuit Breaker Panel
 1) 7G6, SPEED BRAKE AUTO CONT

 

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-10
 ALL  ú ú 04 Page 401 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE  A 
FLIGHT COMPARTMENT 
SPEED BRAKE 
DRUM MECHANISM 

SPEED BRAKE
ARM SWITCH, S217
CONTROL LEVER
FWD
SEE B
1
A  CAM
ARM SWITCH 1 
(1.78-2.29 mm) 0.07-0.09 INCH POINT SWITCH ACTUATION  STRIKER PLATE ARM SWITCH 1 
1  SPEED BRAKE CONTROL LEVER IN THE DOWN POSITION  B 
Figure 401 Automatic Speed Brake Arm Switch Installation 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 7(25)