(2)
IPC 27-81-16 Fig. 1
(3)
IPC 27-81-51 Fig. 1
(4)
SSM 27-81-04, 27-81-05, 27-81-06
(5)
WDM 27-81-31, 27-81-32, 27-81-81, 27-81-82
C.
Access
(1)
Location Zone
513 Krueger Flap Midflap, LH
613 Krueger Flap Midflap, RH
D.
Procedure
S 026-002
(1)
Do this task: "Offset Gearbox Removal" (Ref 27-81-16/401).
S 226-003
(2)
Do a check of the offset gearbox (Fig. 601):
(a)
Use a micrometer to measure the dimensions of the necessary parts.
(b)
Measure the spline backlash on 0.075 inch pitch diameter.
(c)
Measure the backlash on 0.605 to 0.645 inch diameter on the pinion shaft with 5 to 10 pound-inches force applied.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-16
ALL ú ú 01 Page 601 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE A
1. COUPLING
3. INPUT HALF/PINION
DRIVE
SHAFT
OFFSET GEARBOX
3. OUTPUT DRIVE SHAFT
2. PINION/GEAR
A
Krueger Flap Offset Gearbox Wear Limits Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-16
ALL ú ú 01 Page 602 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
INDEX NO. PART NAME DIM. DESIGN LIMITS WEAR LIMITS REPLACE PART WORN REPAIR WORN PART REPAIR INSTR
DIAMETER WEAR DIM. MITTED PER- MAX CLEAR-ANCE DIA
MIN MAX
1 COUPLING HALF 1 0.0982 0.0994 0.1082 0.010 3 X
PINION 2 0.0970 0.0982 0.0882 X
2 PINION 0.012 4 X
GEAR X
CIRCULAR SPLINE SPACE WIDTH CIRCULAR SPLINE TOOTH THICKNESS SPLINE BACKLASH TOTAL BACKLASH
Krueger Flap Offset Gearbox Wear Limits
Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-16
ALL ú ú 01 Page 603 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(d) Measure the permitted axial play of the bearings and the axial play of the gear/bearing:
NOTE: A worn bearing is the primary cause for an offset
____
gearbox replacement.
1) Measure the axial play at the input or output shaft. a) If the axial play is less than 0.022 inch, the bearings are serviceable. b) If the axial play is more than 0.045 inch, replace the gearbox or the worn parts. c) If the axial play is between 0.023 and 0.045 inch, measure the permitted radial shaft play.
2) Measure the radial shaft play at a point on the input or output shaft 1.73 +/- 0.03 inch from the joint face of the gearbox halves. a) Replace the gearbox or the worn parts if the radial
shaft play is 0.005 inch. 3) Make sure the offset gearbox operates smoothly after the axial play check.
S 426-004
(3) Do this task: "Offset Gearbox Installation" (Ref 27-81-16/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-16
ALL ú ú 01 Page 604 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
1.
2.
3.
4.
A
747-400 MAINTENANCE MANUAL
LEADING EDGE FLAP POSITION INDICATING SYSTEM -
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 7(147)
