曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 NOTE:____ PDU (not installed on airplane) is sensitive to orientation when it is filled with oil on the ground. If it is filled with oil and tipped on its side (or upside down), oil can accumulate in the gearbox breather and on the first operation after installation, oil will spray out on the unit and PDU will look like having an oil leak.
 (3)  S 642-022Lubricate the o-rings (15) for pneumatic fittings with silicone fluid.
 (4)  S 422-163Install the o-rings (15).
 (5)  S 822-023Align the pneumatic duct (16) with the pneumatic outlet on the PDU.
 (6)  S 822-164Align the sleeve and the retainer (14).
 (7)  S 432-165Tighten the retainer screw to 3-5 pound-inches more than the run-on torque.
 (8)  S 432-024Connect these primary (pneumatic) drive power electrical connectors (13): (a) DM876 and DM885 (PDU No. 1) (b) DM878 and DM883 (PDU No. 2) (c) DM879 and DM882 (PDU No. 3) (d) DM880 and DM881 (PDU No. 4)
 (9)  S 432-025Connect these alternate (electrical) drive power electrical connectors (33): (a) DM876B and DM885B (PDU No. 1) (b) DM878B and DM883B (PDU No. 2) (c) DM879B and DM882B (PDU No. 3)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-03
 ALL  ú ú 01 Page 216 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (d) DM880B and DM881B (PDU No. 4) S 092-026
 WARNING:_______ YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
 LE FLAP SAFETY LOCKS.  THE LE FLAPS CAN MOVE QUICKLY IF YOU DO
 NOT DO THE STEPS CORRECTLY.  THIS CAN CAUSE INJURY TO PERSONS

 OR DAMAGE TO EQUIPMENT.
 (10)
 Do this task:  "Safety Lock Removal and Leading Edge Flap Activation" (Ref 27-81-00/201).

 S 862-027

 (11)
 Do this task: "Supply Electrical Power" (Ref 24-22-00/201).

 S 862-028

 (12)
 Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6 Main Power Distribution Panel 1) 6L21 LE FLAP ELEC CONT GRP B DRIVE 1 2) 6L22 LE FLAP ELEC CONT GRP A DRIVE 2 3) 6L23 LE FLAP ELEC CONT GRP A DRIVE 3 4) 6L24 LE FLAP ELEC CONT GRP A DRIVE 4 5) 6E3 PRIM LE FLAP CONT GRP A AC 6) 6E4 PRIM LE FLAP CONT GRP A DC 7) 6E5 PRIM LE FLAP CONT GRP B AC 8) 6E6 PRIM LE FLAP CONT GRP B DC

 (b)  
P7 Overhead Circuit Breaker Panel 1) 7C10 FLT CONT ELEC 2L-AC 2) 7C11 FLT CONT ELEC 2L-DC 3) 7C12 FLT CONT ELEC 1L-AC 4) 7C13 FLT CONT ELEC 1L-DC 5) 7C14 FLT CONT ELEC 1R-AC 6) 7C15 FLT CONT ELEC 1R-DC 7) 7C16 FLT CONT ELEC 2R-AC 8) 7C17 FLT CONT ELEC 2R-DC

 (c)  
P414 Power Distribution Center - Left 1) 414A5 LE FLAP ELEC DRIVE 1 2) 414A2 LE FLAP ELEC DRIVE 4

 (d)  
P415 Power Distribution Center - Right 1) 415M35 LE FLAP ELEC DRIVE 2 2) 415B32 LE FLAP ELEC DRIVE 3

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-03
 ALL  ú ú 01 Page 217 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 862-156
 WARNING:_______ MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
 FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP
 CONTROL LEVER.  WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL
 MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP
 CONTROL LEVER.  THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO
 EQUPIMENT.

 (13) Make sure that the flap control lever is in the 5 unit detent (minimum) and in the same position as the trailing edge (TE) flaps.
 NOTE: This check is to make sure that the flaps will not move
____ suddenly when you supply pneumatic and hydraulic power.
 S 862-030
 (14)
 Do this task: "Supply Pneumatic Power" (Ref 36-00-00/201).

 S 222-191

 (15)
 Do a check of the Leading Edge Flap Drive Unit pneumatic fitting for leakage.

 (a)  
If there is excessive leakage, change the fitting o-rings or repair the fitting.

 S 862-031
 (16) Do this task to pressurize hydraulic systems No. 1 and 4: "Hydraulic System Pressurization" (Ref 29-11-00/201).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 7(103)