EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 79-00-00
 ALL  ú ú C02 Page 610 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
6
_
 7
_
 8
_
 9
_
Do a check for pieces of the TGB bearing race crimped retention ring.
 a. If you find flat, rectangular pieces (0.2 inch
_ (4 mm) in width and of different lengths) that are black and curled on the ends, replace the TGB (AMM 72-62-01/401).
Do a check for glass fiber with polymide material (reddish-brown color) or phenolic/plastic material.
 NOTE: These materials are an indication of damage
____ to the aft or forward air/oil seal material in the forward sump of the engine.
 a. If you find these materials, do a check to make
_ sure the oil pressure and consumption are satisfactory.
 b. If the oil pressure and consumption are
_ satisfactory, continue the engine in operation.
 c. Do a check of the oil pressure and consumption
_
 during the next 100-200 hours of operation.Do a check for Torlon resin or polymide material (green color).
 NOTE: This material is an indication of damage to
____ the forward air/oil separator sleeves.
 a. If you find Torlon material, do a check to make
_ sure the oil pressure and consumption are satisfactory.
 b. If the oil pressure and consumption are
_ satisfactory, continue the engine in operation.
 c. Do a check of the oil pressure and consumption
_
 during the next 100-200 hours of operation.Do a check for the rubstrip material of the labyrinth seal, stainless steel particles, or coatings such as silver plate.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 79-00-00
 ALL  ú ú C02 Page 611 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
a.  The engine is serviceable if you find these
_ materials. 10 Do a check for materials such as o-rings, or
__ contamination that has a black color or contains carbon material.
 a.  If you find these materials, do a check to make
_ sure the oil pressure and consumption are satisfactory.
 b.  If the oil pressure and consumption are
_ satisfactory, continue the engine in operation.
 c.  Do a check of the oil pressure and consumption
_ during the next 100-200 hours of operation.
 2)  If the CFMI Non-Destructive Test Manual (NDTM), Part 10, and Tooling photographs are not available and you find magnetic material that you cannot identify, do the steps
________ ______ and obey the limits that follow: a) SATISFACTORY CONDITION - If you find less than four____
______________________ magnetic particles and the largest of the particles is less than 0.01 inch (0.25 mm) in all dimensions, do the step that follows: 1_Continue the engine in service. The operator may
 reduce the MCD inspection interval to 50 hours. If no more particles are found, return to the normal check interval for the MCD.
 b)  MARGINAL CONDITION - If you find more than four____
__________________ magnetic particles and the largest of the particles is less than 0.01 inch (0.25 mm) in all dimensions, do the steps that follows: 1 Send the particles to the laboratory for analysis.
_ 2 Until you get the analysis results from the
_ laboratory, do the inspection of the MCD for particles after each flight.
 3  After you receive the analysis results, refer to,
_ in this task, paragraph E.(3)(d)1 ) ("If you can identify the contamination material...") and take the appropriate action.
 c)  MARGINAL CONDITION - If you find less than four____
__________________ magnetic particles and the largest of the particles is more than 0.01 inch (0.25 mm) but less than 0.02 inch
 (0.50 mm) in all dimensions, do the steps that follows: 1 Send the particles to the laboratory for analysis.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 滑油 OIL(7)