79-21-01
ALL ú ú C02 Page 403 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
BOLT
(4 LOCATIONS
AFT SUMP OIL FOR EACH TUBE)
SCAVENGE TUBE FORWARD SUMP
SCAVENGE TUBE
LUBE
SUPPLY
TUBE
AGB
SCAVENGE
TUBE
TUBE
BUNDLE CLAMP
LUBRICATION
UNIT CLAMP
FWD
B
Lubrication Unit Installation
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
79-21-01
ALL ú ú C02 Page 404 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(b) Remove the inlet and outlet pressure tubes from the pressure
switch and scavenge filter.
NOTE: It can be necessary to loosen the clamp between the
____ inlet and outlet pressure tubes for the removal.
1) Discard the o-rings.
(c) Remove the pressure switch bracket from the lubrication unit.
1) ENGINES PRE-CFMI-SB 79-028; If the bracket with a washer and a large (0.285 inch) bolt hole is used, remove and keep the washer.
S 034-006-C00
(6)
Remove the magnetic chip detectors (MCD's) (AMM 79-21-05/201).
S 684-007-C00
(7)
Drain the oil from the lubrication unit as follows:
(a)
Put the drain adapter into the lubrication unit at the MCD
location.
(b)
Push the adapter in and turn it one quarter turn clockwise.
(c)
Permit the oil to drain into the container.
(d)
Remove the drain adapter:
1) Push in while you turn it one quarter turn
counterclockwise.
2) Pull the adapter down and remove it from the lubrication unit.
(e)
Drain the oil from the lubrication unit at the two MCD
locations that remain.
S 434-008-C00
CAUTION: DO NOT INSTALL THE MAGNETIC PLUG WITHOUT AN O-RING.
_______ INSTALLATION OF THE MAGNETIC PLUG WITHOUT AN O-RING CAN CAUSE OIL LEAKAGE DURING ENGINE OPERATION AND A POSSIBLE ENGINE FAILURE.
(8)
Clean and install the MCD's (AMM 79-21-05/201).
S 034-044-C00
(9)
Remove the clamp that attaches the oil supply tube to the inlet tube of the scavenge oil filter.
(10)
Remove the inlet tube of the scavenge oil filter.
S 034-010-C00
NOTE: Gaskets can be used again if they are in a good condition.
____
S 034-011-C00
(11) Disconnect the forward and aft sump oil supply tubes from the lubrication unit.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
79-21-01
ALL ú ú C03 Page 405 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 034-012-C00
(12)
Remove the AGB oil supply tube.
S 034-013-C00
(13)
Disconnect the aft scavenge tube, forward scavenge tube and lube supply tube from the lubrication unit.
S 034-014-C00
(14)
Remove the AGB scavenge tube.
NOTE: Gaskets can be used again if they are in good condition.
____
S 034-015-C00
(15) Remove the tube bundle clamp aft of the lubrication unit.
S 034-016-C00
CAUTION: HOLD THE LUBRICATION UNIT WHEN YOU REMOVE THE ATTACHMENT CLAMP.
_______ DO THIS TO PREVENT DAMAGE TO THE DRIVE SHAFT AND SPLINES.
(16)
Remove the clamp that attaches the lubrication unit to the AGB.
S 024-017-C00
(17)
Remove the lubrication unit:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 滑油 OIL(21)
