(c)  
Do the indicator adjustment at all oil changes, when you change the indicator and when you change the engine.

 (d)  
When calibrated with the above procedure, the oil quantity indicator will show the useable quantity of oil in the tank.

 B.  Approximately 1-2 quarts of oil are in the engine sump.
 (1)  This oil is not useable by the engine and is not measured by the indicator system.
 TASK 79-31-00-715-001-C00
 2.  Operational Test - Oil Quantity Indicating System
_________________________________________________
 A.  General
 (1)  
This test can be conducted when only a tank unit is changed.

 (2)  
If you think the indication is incorrect, after the installation, the system test is necessary to calibrate the system again.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-31-00
 ALL  ú ú C02 Page 501 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
B.  References
 (1)  
AMM 12-13-11/301, Engine Oil Servicing

 (2)  
AMM 24-22-00/201, Manual Control

 C.  Access
 (1)  
Location Zones
 506 Engine No. 1
 606 Engine No. 2

 (2)  
Access Panels
 5737L/5746L Engine No. 1 - Fan Cowl Assembly
 5837R/5846R Engine No. 2 - Fan Cowl Assembly

 D.  Prepare to Do the Operational Test
 S 615-002-C00
 (1)  
Make sure the engine oil tank is full (AMM 12-13-11/301).

 S 865-004-C00

 (2)  
Supply the electrical power (AMM 24-22-00/201).

 (a)  Remove the DO-NOT-OPERATE tag from the BAT switch.
 S 865-003-C00
 (3)  Make sure these circuit breakers are closed:
 (a)  P6-2 Load Control Center 1) For Engine No. 1: a) AIRPLANES WITHOUT THE ENGINE INSTRUMENT SYSTEM (EIS); ENG 1 OIL QTY b) AIRPLANES WITH THE ENGINE INSTRUMENT SYSTEM (EIS); EIS SEC 1 2) For Engine No. 2: a) AIRPLANES WITHOUT THE ENGINE INSTRUMENT SYSTEM (EIS); ENG 2 OIL QTY
 b)  AIRPLANES WITH THE ENGINE INSTRUMENT SYSTEM (EIS); EIS SEC 3
 E.  AIRPLANES WITH OIL TEMPERATURE INDICATORS; (AIRPLANES WITHOUT THE ENGINE INSTRUMENT SYSTEM (EIS)); Do the Operational Test
 S 215-007-C00
 (1)  The oil quantity indicator must read 4.5 gallons for engine No. 1 or
 4.75 gallons for engine No. 2 (on airplanes with indicators graduated from 0 to 4 1/2 U.S. gallons) or 17 liters for engine No. 1 or 18 liters for engine No. 2 (on airplanes with indicators graduated from 0 to 18 liters).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-31-00
 ALL  ú ú C02 Page 502 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 865-010-C00
 (2)  Push and hold the ENG OIL QTY TEST switch on the pilots center instrument panel P-2.
 (a)  The indicator pointer will start to move to zero.
 S 865-011-C00
 (3)  Release the ENG OIL QTY TEST switch.
 (a)  The indicator pointer will go back to its initial value.
 S 865-125-C00
 (4)  Open these circuit breakers and attach DO-NOT-CLOSE tags:
 (a)  P6-2 Load Control Center
 1) For Engine No. 1:
 a) ENG 1 OIL QTY

 2)  For Engine No. 2:
 a) ENG 2 OIL QTY

 S 215-015-C00
 (5)  
Make sure the indicator shows full.

 S 865-126-C00

 (6)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  P6-2 Load Control Center
 1) ENG 1 OIL QTY
 2) ENG 2 OIL QTY

 S 865-023-C00
 (7)  Remove the electrical power (AMM 24-22-00/201).
 (a)  Set the BAT switch on the Electrical Meters Battery and Galley Power Module (P5-13) to the OFF position and install a DO-NOT-OPERATE tag.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 滑油 OIL(43)