S 094-011-C00

 (3)  
Remove the cover from the sensing element.

 S 424-012-C00

 (4)  
Attach the element to the fan inlet duct with four bolts.

 S 434-013-C00

 (5)  
Tighten the bolts to 55-70 pound-inches (6-8 Newton meters).

 S 434-012-C00

 (6)
Attach the capillary tube to the fan case brackets with 2 clamps.

 S 094-013-C00

 (7)  
Remove the caps from the P7 and the PB fuel tubes and the fittings on the sensor housing.

 S 434-014-C00
 CAUTION:_______USE TWO WRENCHES TO INSTALL THE TUBE COUPLING NUTS. USE ONE WRENCH TO HOLD THE NIPPLE. USE THE OTHER WRENCH TO TIGHTEN THE NUT. THIS IS TO PREVENT DAMAGE TO THE HARDWARE.
 (8)  Connect the P7 tube to the fitting on the sensor housing.
 (a)  Tighten the tube nut to 270-300 pound-inches
 (30.5-33.9 Newton meters).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-21-09
 ALL  ú ú C01 Page 405 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 434-015-C00
 (9)  Connect the PB tube to the fitting on the sensor housing.
 (a)  
On engines with PB tube P/N 335-208-801-0, tighten the tube nut to 280 pound-inches (32 Newton meters).

 (b)  
On engines with PB tube P/N 335-208-803-0, tighten the tube nut to 195-210 pound-inches (22-24 Newton meters).

 S 434-016-C00
 (10) Install Pro Seal 860 sealant around the element base in the inlet cowl.
 NOTE: This is to make sure of smooth air flow near the element.
____
 S 414-017-C00
 (11)
 Close the left fan cowl panel (AMM 71-11-02/201).

 S 794-018-C00

 (12)
 Do a leak check - idle power (AMM 71-00-00/501).

 S 204-020-C00

 (13)
 Do a Main Engine (MEC) Trim Check (AMM 71-00-00/501, Test No.6).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-21-09
 ALL  ú ú C02 Page 406 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
T2 TEMPERATURE SENSOR - INSPECTION/CHECK
________________________________________
 1.  General
_______
 A.  You must do two checks to do an inspection of the T2 Temperature Sensor.
 (1)  
A visual check of the components that follow is given in task 2:

 -
the sensor housing

 -
the PB and P7 fittings

 -
the mounting flanges

 -
the capillary tube.

 (2)  
An internal failure check is given in task 3.

 B.  Removal of the sensor from the engine is not necessary for these
 inspections.

 TASK 73-21-09-206-001-C00
 2.  Visual Check of the T2 Temperature Sensor
_________________________________________
 A.  References
 (1)  AMM 71-11-02/201, Fan Cowl Panels
 B.  Access
 (1)  
Location Zones 506 Engine No. 1 - left side of the fan case at the 10:30 o'clock position

 606  Engine No. 2 - left side of the fan case at the 10:30 o'clock position

 (2)  
Access Panels
 5746L Engine No. 1 - Left Fan Cowl Panel
 5846R Engine No. 2 - Left Fan Cowl Panel

 C.  Procedure (Fig. 601)
 S 016-002-C00
 (1)  
Open the left fan cowl panel (AMM 71-11-02/201).

 S 216-003-C00

 (2)  
Examine the sensor housing for the conditions that follow:

 (a)  
Cracks 1) If it is not serviceable, replace the sensor.

 (b)  
Nicks and scratches 1) There is no limit on the number and dimension.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機燃油和控制(136)