73-21-02
ALL ú ú C02 Page 402 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
LINES FUEL DRAINS SHROUD
SEE A
SEE C P6 FITTING
FITTING PB
SEE B
OF THE ENGINE CENTERLINE VERTICAL BOTTOM 15` FWD A SEE D
6P CONNECTIONS TO THE CIT SENSOR FUEL LINE
BP P6 DRAIN TUBE
O'CLOCK 6:00 STRUT 5:30 O'CLOCK
FORWARD VIEW B PB DRAIN TUBE
C
Compressor Inlet Temperature (CIT) Sensor Installation Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-02
ALL ú ú C01 Page 403 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
DRAIN LINE
O-RING
FAN FRAME
SHROUD
O-RING
O-RING
FUEL LINE
(P6 OR PB) FITTING
SLEEVE
THREADED
LOCK WIRE FLANGE
COUPLING
NUT
O-RING D
COIL GUARD
MOUNTING FLANGE
P6 FITTING
HOUSING
PB FITTING
CIT SENSOR - REMOVED
Compressor Inlet Temperature (CIT) Sensor Installation
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-02
ALL ú ú C01 Page 404 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE A
SEE B
SEE B6 0'CLOCK STRUT
A
SEE C
CAPTIVE BOLT (8 LOCATIONS) FAN DUCT PANEL
FAN DUCT PANEL CAPTIVE BOLT SEALANT B
FRAME FAN
SEALANT BUSHING RETAINING WASHER
C
Figure 402 Fan Duct Panel Installation
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-02
ALL ú ú C01 Page 405 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 034-008-C00
(7) Remove the lockwire from the coupling nut.
(a) Disconnect the coupling nuts from the sensor fittings.
S 024-009-C00
CAUTION: THE SENSOR IS SENSITIVE. CAREFULLY
_______DO NOT HANDLE ROUGHLY. HANDLE THE SENSOR TO PREVENT DAMAGE TO THE COIL, TUBE FITTINGS AND THE MATING FLANGE. DO NOT REPAIR THE INTERNAL PARTS OF THE SENSOR OR THE COIL.
HOLD THE CIT SENSOR WHEN YOU REMOVE THE LAST BOLT TO MAKE SURE THE SENSOR WILL NOT FALL. IF YOU DO NOT OBEY THESE PRECAUTIONS, DAMAGE TO THE EQUIPMENT CAN OCCUR.
(8) Do these steps to remove the sensor:
(a) Remove the 4 bolts that attach the sensor to the fan frame pad.
CAUTION: DO NOT PERMIT THE PERMANENT DEFORMATION OF THE FUEL TUBES
_______ WHILE YOU MOVE THEM. IF YOU DO NOT OBEY THIS PRECAUTION, DAMAGE TO THE EQUIPMENT CAN OCCUR.
(b)
Hold the sensor with your hand. 1) Carefully move the fuel tube to be clear of the fittings on the sensor.
2) Move the fuel tubes only a sufficient distance to be clear of the fittings.
(c)
Carefully move the body of the sensor forward to permit the sensor coil to clear the fan frame port. 1) Pull the sensor from the fan frame.
NOTE: Be careful not to damage the sealing surfaces on the
____ sensor fuel fittings.
(d)
Remove the O-rings from the grooves on the sensor fuel fittings. 1) Discard the O-rings.
(e)
Install the dust caps on the fuel fittings to keep the unwanted material out of the sensor.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機燃油和控制(114)
