73-21-05
ALL ú ú C01 Page 602 ú Jul 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(c) 2) If more than the limits, replace the sensor (AMM 73-21-05/401).Dirt build-up in air inlet or exit slots 1) If amount blocks free passage of air, clean with bristle brush and solution of water and mild detergent.
S 036-004-C00
(3) Disconnect the electrical connector from the sensor.
NOTE:____ It may be necessary to use padded-jaw pliers to loosen the electrical connector.
S 216-005-C00
(4) Examine the electrical connector for the conditions that follow: (a) Thread damage 1) Repair the threads if less than 20 percent are damaged. 2) Replace the sensor (AMM 73-21-05/401) if more than 20 percent are damaged. (b) Pin damage 1) Make straight any bent pins. 2) Replace the sensor (AMM 73-21-05/401) if any pins are broken, eroded or seized. (c) Dirt build-up in connector well 1) Clean with a bristle brush and solvent.
S 766-006-C00
(5) Do an insulation resistance check: (a) Measure the resistance between pin 1, pin 2, pin 4 and the receptacle body. (b) If the resistance is less than 10 megaohms, replace the sensor (AMM 73-21-05/401).
S 436-007-C00
(6) Connect the electrical connector to the sensor. (a) Engage the connector with its mating interface. (b) Turn the knurled coupling ring with your hand while you move the back shell assembly. (c) Tighten the coupling ring with the padded-jaw pliers. (d) Make sure the connector is fully engaged.
NOTE:____ There must not be any movement of the connector.
S 416-008-C00
(7) Close the right fan cowl panel (AMM 71-11-02/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-05
ALL ú ú C01 Page 603 ú Jul 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
CFMI WIRING HARNESS - REMOVAL/INSTALLATION
__________________________________________
1. General
_______
A. The CFMI wiring harness has two cable assemblies: the control parameter wiring harness and the N2 control alternator speed sensor cable.
NOTE: These two cables are installed on the engine by the engine
____ manufacturer and are blue in color. All wiring with a color of red and grey is installed by the airplane manufacturer.
B. The wiring harness for the control parameter is found between the MEC and the PMC, with more connections to the N1 speed sensor and the T12 temperature sensor, and is put below the engine fan case.
C. The speed sensor cable for the N2 control alternator is found between the N2 control alternator and the PMC and put on the top of the fan case.
TASK 73-21-06-004-001-C00
2. Wiring Harness for the Control Parameter Removal
________________________________________________
A. General
(1) For this procedure the wiring harness for the control parameter will be referred to as the wiring harness.
B. Equipment
(1) Pliers - padded jaw - connector type 8498-03
C. References
(1) AMM 71-11-02/201, Fan Cowl Panels
D. Access
(1)
Location Zones
502/602 Left Fan Cowl Panels
503/603 Right Fan Cowl Panels
506 Engine No. 1 - Fan Frame
606 Engine No. 2 - Fan Frame
(2)
Access Panels
5737L Engine No. 1 - Right Fan Cowl Panel
5746L Engine No. 1 - Left Fan Cowl Panel
5837R Engine No. 2 - Right Fan Cowl Panel
5846R Engine No. 2 - Left Fan Cowl Panel
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機燃油和控制(127)
