(b)  
P414 Power Distribution Center-Left
 1) 414M8 CABIN PRESS ICU LEFT
 2) 414B8 CABIN PRESS ICU RIGHT

 (c)  
P83 in aft equipment center
 1) OUTFLOW VALVE-R
 2) OUTFLOW VALVE-L

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-31-06
 ALL  ú ú 01 Page 401 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
AFT BULKHEAD ACCESS DOOR
SEE A BOLT AND WASHER
BULK CARGO COMPARTMENT
(4 LOCATIONS)
FWD PACKING AC MOTOR
ACTUATOR HOUSING BEARING COVERPLATE
ACTUATOR  SEE  B  1 
OUTPUT  OUTFLOW 
LEVER  VALVE 
ACTUATOR 
BEARING 
COVERPLATE 
ACTUATOR 
HOUSING 

PIN
SLOTTED KEY
OUTFLOW VALVE
BEARING COVERPLATE A B1
1
MPC AC MOTORS PRE-HAMILTON STANDARD-SB 21-193; AEROFLEX OR HAROWE AC MOTORS
Outflow Valve AC Motor Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-31-06
 ALL  ú ú 01 Page 402 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 014-003
 (2)  
Remove the access panel from the aft bulkhead of the bulk cargo compartment to get access to the outflow valves.

 S 014-004

 (3)  
Remove the safety screen.

 S 034-005

 (4)  
Remove the electrical connector from the AC motor:

 (a)  
The AC motor electrical connector for the left valve - DV91A

 (b)  
The AC motor electrical connector for the right valve - DV90A.

 S 024-006
 (5)  
Remove the bolts and washers from around the AC motor and remove the AC motor and the packing from the valve actuator.

 S 034-007

 (6)  
Remove the packing from the AC motor.

 TASK 21-31-06-404-008
 3.  Outflow Valve AC Motor Installation___________________________________
 A. Consumable Materials
 (1)  D00378 Grease - Mobil No. 28 or equivalent
 B. References
 (1)  
AMM 21-31-00/501, Cabin Pressure Control System

 (2)  
AMM 24-22-00/201, Manual Control ectrical Power

 (3)  
AIPC 21-31-01, Fig. 1

 (4)  
WDM 21-31-13

 (5)  
SSM 21-31-02

 C. Access
 (1)  Location Zone
 151 Area Aft of Bulk Cargo Compartment, LH
 152 Area Aft of Bulk Cargo Compartment, RH

 D. Procedure
 S 434-009
 (1)  Put the packing on the AC motor.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-31-06
 ALL  ú ú 01 Page 403 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (2)  S 644-024Fill the teeth of the ac motor output pinion with Mobil Grease No. 28, or the equivalent.
 (3)  S 824-010Turn the valve actuator output lever in a counterclockwise direction until it is against its stop at the open position.
 S 214-011

 CAUTION:_______MAKE SURE THE KEY IS INSTALLED AND ALIGNED CORRECTLY. IF THE KEY IS MISSING OR NOT ALIGNED CORRECTLY, THE GEAR SHAFT MAY DAMAGE THE GEARBOX.
 (4)  AIRPLANES INSTALLING MPC AC MOTORS PRE-SB 21-193 (HAMILTON STANDARD), AND HAROWE/AEROFLEX AC MOTORS: Make sure the key and the pin are installed in the coverplate slot.
 NOTE: MPC ac motors post-SB 21-193 (Hamilton Standard) do not
____ require the coverplate or slotted key.
 S 424-012
 (5)  Put the AC motor in its position on the actuator housing and install the washers and bolts. Tighten the bolts to 10-15 inch-pounds (1.1 to 1.7 Newton-meters) above the run-on torque.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AIR CONDITIONING 1(121)