B. Equipment
(1) Socket Wrench, ST 2580-177
C. References
(1) AIPC 54-42-50
D. Access
(1) Location Zones
500 Left Nacelle
600 Right Nacelle
E. Procedure
S 012-030-B00
(1)
Do this task: Get Access to the Hinges for the Thrust Reverser.
(2)
Remove the ball from the race.
(3)
Remove the race from the thust reverser hinge.
S 032-016-B00
S 022-074-B00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
54-42-13
ALL ú ú B04 Page 221 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 162-018-B00
(4)
Clean the thrust reverser hinge.
S 212-019-B00
(5)
Examine the thrust reverser hinge for damage (SRM 54-50-90).
S 412-031-B00
(6)
Do this task: Bearing Assembly Installation, Center Fitting.
TASK 54-42-13-022-015-B00
14. Cross Beam Removal, Center Fitting (Fig. 203)__________________________________
A. References
(1) AIPC 54-42-50
B. Access
(1) Location Zones
500 Left Nacelle
600 Right Nacelle
C. Procedure
S 012-034-B00
(1)
Do this task: Get Access to the Hinges for the Thrust Reverser.
S 022-035-B00
(2)
Remove the nut, washers, and bolt.
S 022-036-B00
(3)
Remove the jumper from the clip.
S 022-037-B00
(4)
Remove the nut, washer, bushing, jumper, washer, and bolt.
(5)
Remove the ball from the race.
S 022-038-B00
S 022-072-B00
CAUTION:_______ USE CARE AS YOU SLIDE THE CROSS BEAM THROUGH EACH CLEVIS AND
ABOVE THE HEAT SHIELD. MAKE SURE THE CROSS BEAM IS FREE TO
MOVE. AS THE CROSS BEAM LUG STARTS INTO THE OPPOSITE CLEVIS,
DO A CHECK OF THE ALIGNMENT. THE BUSHINGS ON THE CROSS BEAM
CAN BE CAUGHT ON THE BUSHINGS OF THE HINGE FITTING AND CAUSE
DAMAGE.
(6)
Carefully pull the cross beam out of the strut. S 202-041-B00
(7)
Examine the cross beam for damage.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
54-42-13
ALL ú ú B03 Page 222 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 202-040-B00
(8) Examine the hinge fitting for damage.
TASK 54-42-13-022-016-B00
15. Vibration Isolator Removal, Center Fitting (Fig. 203)
__________________________________________
A. References
(1) AIPC 54-42-50
B. Access
(1) Location Zones
500 Left Nacelle
600 Right Nacelle
C. Procedure
S 012-042-B00
(1)
Do this task: Get Access to the Hinges for the Thrust Reverser.
S 022-043-B00
(2)
If it is necessary, do this task: Cross Beam Removal, Center Fitting.
S 022-044-B00
(3)
Remove the isolator from the bushing.
NOTE: Replace both isolators for each hinge fitting at the same
____
time.
S 402-045-B00
(4)
Examine the bushing for damage.
(5)
Examine the center hinge fitting for damage.
S 402-046-B00
TASK 54-42-13-422-021-B00
16. Bearing Assembly Installation, Center Fitting Cross Beam (Fig. 203)
________________________________________________________
A. Equipment
(1) Socket Wrench, ST 2580-177
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 NACELLES/PYLONS(55)
