(b)
Turn the captain's control wheel counterclockwise 87 degrees minimum from the neutral position.
(c)
Make sure that the left aileron moves up and the right aileron moves down in the specified limits (Fig. 506).
(d)
Turn the captain's control wheel clockwise 87 degrees minimum from the neutral position.
(e)
Make sure that the left aileron moves down as specified (Fig. 506).
(f)
Make sure that the right aileron moves up as specified (Fig. 506).
(g)
Release pressure from hydraulic systems A and B
(AMM 27-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-00
ALL ú ú 02 Page 525 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
A
Autopilot Control Component Locations
Figure 509
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-00
ALL ú
ú 01 Page 526
ú Oct 25/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
MIDDLE POINT ALONG THE AILERON BALANCE TAB
A STRAIGHT EDGE IS SHOWN, YOU CAN ALSO USE AN AILERON TAB ALIGNMENT PROTRACTOR - F80222-1.
Aileron Tab Alignment
Figure 510
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-00
ALL ú ú 01 Page 527 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 735-047
(6) Measure the distance from the tab trailing edge to the extension of the aileron bottom surface with a straightedge or an aileron tab alignment protractor.
NOTE: The index mark on the aileron (Point B) must align with the
____ index mark on the wing (Point A) to 0.03 inch or less when you do this check.
If the tab trailing edge is above the extension of the aileron bottom surface, write down a plus (+) dimension. If the tab trailing edge is below the extension of the aileron bottom surface, write down a minus (-) dimension.
(a) Measure 0.50 |0.25 inch in from the inboard end of the tab.
1) Make sure the tab trailing edge aligns with the extension of the aileron bottom surface between +0.00 to +0.14 inch (Fig. 510).
2) Write down the distance.
(b) Measure 0.50 |0.25 inch in from the outboard end of the tab.
1) Make sure the tab trailing edge aligns with the extension of the aileron bottom surface between +0.00 to +0.14 inch (Fig. 510).
2) Write down the distance.
(c) Measure at the middle point along the tab.
1) Make sure that the tab trailing edge aligns with the extension of the aileron bottom surface between +0.05 to +0.09 inch (Fig. 510).
2) Write down the distance.
(d)
Add the total distances measured at three different points along the tab.
(e)
Make sure the sum of these distances is between +0.30 and +0.12 inch.
S 495-048
(7) With a straightedge or an aileron tab alignment protractor, measure each aileron tab movement.
NOTE: Measure from a point along the trailing edge of the tab to
____
the extension of the aileron bottom surface.
(a)
Manually move the aileron 3.81 inches down from the index mark on the wing.
(b)
Make sure that the tab moves up 1.25 |0.07 inches.
(c) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(91)
