E.  
Use the Aileron Tab Alignment Protractor to Measure the Aileron Tab Movement

 S 482-025
 (1)  
Use the protractor to measure the aileron tab movement:

 (a)  
Make sure that the aileron aligns with the index mark on the wing (use a tolerance of + /- 0.03 inch).

 (b)  
Move the protractor to a point along the aileron tab.

 (c)  
Move the protractor forward until the scale lightly touches the aileron tab.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-94
 ALL  ú ú 01 Page 201 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

PROTRACTOR SCALE
Aileron Tab Alignment Protractor
Figure 201

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-94
 ALL  ú ú 02 Page 202 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (d)  
Adjust the scale on the protractor to align the index mark on the scale with the aileron tab trailing edge.

 (e)  
Move the aileron up or down to its limit with the protractor held in its position.

 (f)  
Measure the aileron tab movement with the scale on the protractor.

 TASK 27-09-94-482-026
 3.  Elevator Index Plate Rigging Beam Usage
_______________________________________
 A.  General
 (1)  
You can use the elevator index plate rigging beam to install or adjust the elevator index plates. Installation or adjustment of the elevator index plates is necessary when you replace the tail cone with a new or different tail cone.

 (2)  
Marks on the stabilizer are necessary to correctly use the rigging beam. If these marks are not on the stabilizer, add the marks as shown in Fig. 202.

 B.  
Special Tools and Equipment

 (1)  
F80230-1 - Elevator Index Plate Rigging Beam

 C.  
References

 (1)
AMM 27-41-00/501, Horizontal Stabilizer Trim Control System

 D.  
Access

 (1)  
Location Zones
 711/712 Left/Right Elevator and Tab

 E.  
Use the Elevator Index Plate Rigging Beam to Install or Adjust the Elevator Index Plates

 S 482-027
 (1)  
Use the rigging beam to install or adjust the elevator index plates:

 (a)  
Use a trammel bar or a scale to set the horizontal stabilizer at the "B" dimension of 41.57 |0.01 inches (AMM 27-41-00/501).

 (b)  
Hold the rigging beam on the bottom side of the stabilizer.

 (c)  
Set the index slot located on the front of the rigging beam, to

 6.80 inches inboard of the aligned point Q on the stabilizer.
 NOTE: At this position, the index slot of the rigging beam
____ will align with the mark on the stabilizer.
 (d)  Move the rigging beam forward or aft along the radius arc until the scale of the rigging beam touches the aft edge of the elevator trailing edge.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-94
 ALL  ú ú 02 Page 203 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

A/P

NOTE:UNDERSIDE OF RIGHT STABILIZER IS SHOWN, LEFT STABILIZER IS OPPOSITE.

Elevator Index Plate Rigging Beam
Figure 202 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-94
 ALL  ú ú 02 Page 204 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(66)