27-11-51
 ALL  ú ú 02 Page 405 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 B. Standard Tools and Equipment
 (1)  
Vinyl Plastic Tape - 2 inches wide, Permacel Cold Weather Vinyl Tape No. 295

 C.
Consumable Materials

 (1)  
D00000 Solvent - BMS 3-2

 (2)  
D00000 Grease - Mil-G-25760

 D.
References

 (1)  
AMM 27-11-00/201, Aileron and Aileron Trim Control System

 (2)  
AMM 22-11-11/401, Roll Control Wheel Steering Force Transducer

 (3)  
22-11-13/401, Aileron Force Limiter

 E.
Access

 (1)  
Location Zone
 101 Control Cabin, LH
 102 Control Cabin, RH
 202 Lower Nose Compartment

 (2)  
Access Panel
 1103 Forward Access Door

 F.
Prepare for Removal

 S 014-007
 (1)  
Open the access door of the lower nose compartment.

 S 864-008

 (2)  
Do this task to depressurize hydraulic systems A and B: "Aileron Hydraulic Systems A and B Depressurization" (AMM 27-11-00/201).

 S 864-009

 (3)  
Put the aileron control wheels in the neutral position.

 S 864-010

 (4)  
Make sure the aileron trim control switches are at the zero trim position.

 S 494-011

 (5)  
Install rigging pins A/S-1 and A/S-1A in the aileron transfer mechanism (Fig. 401).

 (a)  
Make sure the rigging pin A/S-1 is fully in the transfer mechanism.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-51
 ALL  ú ú 02 Page 406 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  Hold the rigging pin A/S-1 to make sure it does not fall out.
 S 494-012
 (6)  
Install rigging pin A/S-15 in the aileron trim mechanism.

 G.
Remove the Aileron Control Wheel Drum

 S 024-013
 (1)  
Remove the control wheel drum (Fig. 401):

 (a)  
Disconnect the electrical connector at the roll force transducer.

 (b)  
AIRPLANES WITH THE AILERON FORCE LIMITER; Disconnect the electrical connector at the aileron force limiter.

 (c)  
Remove the cable shields.

 (d)  
Disconnect then attach identification tags on all these cables: 1) The cables ACBA and ACBB at the turnbuckles. 2) The left cables AA and AB at the turnbuckles. 3) The control cables and the brake control cables of the

 landing gear.

 (e)  
Remove the air duct of the control cabin.

 (f)  
Disconnect control cables of the speed brake at the turnbuckles.

 (g)  
Attach identification tags on the disconnected cables.

 (h)  
Remove the nuts, washers and bolts that connect the control wheel drum to the structure.

 (i)  
Move the control wheel drum down while you guide the cables ACBA and ACBB through cutouts until you can remove the assembly from the structure.

 (j)  
Remove the nuts, washers and bolts from the cable guards.

 (k)  
Remove the cable guards.

 (l)  
Disengage the cables AA and AB from the control wheel drum.

 (2)  
Do this task: "Roll Force Transducer Removal" (AMM 22-11-11/401).

 S 024-018

 (3)  
AIRPLANES WITH THE AILERON FORCE LIMITER; Do this task: "Aileron Force Limiter Removal" (AMM 22-11-13/401).

 S 024-014
 TASK 27-11-51-404-004
 3.  Aileron Control Wheel Drum Installation (With Ribs and Brackets Connected)_______________________________________
 A. Special Tools and Equipment
 (1)  SE27-0001 - Straightedge
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-51
 ALL  ú ú 03 Page 407 ú Mar 12/00
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(130)