曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 a) b) c)  Remove the rig pin A/S-4.Loosen the two locknuts on the valve rod for the power control unit at the bottom.Turn the adjustable sleeve until you can easily install rig pin A/S-4.
 (5)  S 865-009Set the FLT CONTROL A switch to the OFF position.
 (6)  S 865-010Set the FLT CONTROL B switch to the ON position. (a) Make sure the rig pin A/S-4 can move freely in the top bus drum. 1) If the rig pin cannot move freely, adjust the valve rod:
 CAUTION:_______ MAKE SURE TO REMOVE THE RIG PIN A/S-4 BEFORE YOU ADJUST THE VALVE ROD. FAILURE TO REMOVE THE RIG PIN A/S-4 CAN CAUSE DAMAGE TO EQUIPMENT.
 a)  Remove the rig pin A/S-4.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-71
 ALL  ú ú 02 Page 505 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 b)  Loosen the two locknuts on the valve rod for the power control unit at the top.
 c)  Turn the adjustable sleeve until you can easily install rig pin A/S-4.
 S 865-012
 (7)  
Set the FLT CONTROL A and B switches to the ON position.

 (a)  
Make sure the rig pin A/S-4 can move freely in the two bus drums.

 (b)  
Make sure the clearances between the lug of the top bus drum and the stop bolts on the bottom bus drum are as specified (Fig. 502). 1) Adjust the valve rods and stop bolts if it is necessary.

 S 095-013
 (8)  
Remove the rig pin A/S-4.

 S 865-014

 (9)  
Turn the aileron control wheel clockwise and counterclockwise from the neutral position.

 (a)  
Make sure the movement of the aileron is in the specified limit (Fig. 501).

 S 435-015
 (10)
 Tighten the valve rod locknuts.

 S 435-016

 (11)
 Tighten the stop bolt locknuts.

 S 435-017

 (12)
 Install the lockwire.

 S 285-018

 (13)
 Do a check of the autopilot system for the correct roll inputs:

 (a)  
Put the A/P ENGAGE A switch to CMD.

 (b)  
Push the HDG SEL button.

 (c)  
Set the BANK LIMIT switch to 10 and HEADING knob to give an indication of 10 degrees to the right of the airplane heading.

 (d)  
Make sure the control wheel turns clockwise.

 (e)  
Do steps (d) again in the left direction.

 (f)  
Make sure the control wheel turns counterclockwise.

 (g)  
Disengage the autopilot.

 E.  
Put the Airplane Back to Its Usual Condition

 S 865-001
 (1)  Do this task to release pressure from hydraulic systems A and B: "Aileron Hydraulic Systems A and B Depressurization" (AMM 27-11-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-71
 ALL  ú ú 01 Page 506 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 865-002
 (2)  Do this task if electrical power is not necessary: "Electrical Power Removal" (AMM 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-71
 ALL  ú ú 01 Page 507 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 AILERON ARTIFICIAL FEEL, CENTERING AND TRIM MECHANISM -
_____________________________________________________ REMOVAL/INSTALLATION
____________________
 1.  General_______
 A.  There are two tasks in this procedure. There is one task for the removal and one task for the installation of the aileron artificial feel, centering and trim mechanism.
 TASK 27-11-81-004-001
 2.  Aileron Artificial Feel, Centering and Trim Mechanism Removal_____________________________________________________________
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(151)