(e) If the ECAM warning clears.
(f) Access the FLP ON GROUND FAULTS, and make sure the ground log is clear.
(g) If the ECAM warning and a ground log message is displayed do the fult isolation.
4. Fault Isolation
_______________
A. Procedure
(1) The SFCC flap system has two (2) reported fault coditions.
(2) Access the LAST LEG REPORT and look for the message " SFCC 1". and ""SFCC 2".
(a) Each SFCC is the subject of the system test (BITE) and each fault is identified as a separate subject.
(b) Do the system test (BITE) (Ref. AMM TASK 27-51-00-740-001) on each SFCC in turn.
(c) Refer the applicable fault symptoms to page block 101 and carry out the related TSM procedure.
5. Close-up
________
A. Remove the ground support and maintenance equipment, the special and standard tools and all other items.
B. Put the aircraft back to its initial configuration.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 242
May 01/04R CES
Left Flap Interconnecting-Strut Attachment Failure-Detection Sensor Fault
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Possible Causes
_______________
- SFCC-1 (21CV)
- SFCC-2 (22CV)
- SENSOR-L FLAP ATTACHMENT FAILURE DETECTION (37CV)
- SENSOR-L FLAP ATTACHMENT FAILURE DETECTION (39CV)
- aircraft wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-31-00-810-828 Left Flap Disconnect Proximity Sensor (37CV, 39CV) AMM 27-51-00-710-002 Operational Test of the Flap Interconnecting Strut and the Flap-Attachment Failure-Detection Sensors AMM 27-51-15-000-002 Removal of the Proximity-Sensors of the Interconnecting Strut AMM 27-51-15-400-002 Installation of the Proximity-Sensors of the
Interconnecting Strut
AMM 27-51-34-000-001 Removal of the SFCC (21CV,22CV)
AMM 27-51-34-400-001 Installation of the SFCC (21CV,22CV)
R AMM 32-69-00-740-001 BITE Check Landing Gear Control Interface Unit R (LGCIU) using MCDU to Ensure that Continuous BITE is R Operative
ASM 27-51/06
ASM 27-51/07
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 243
May 01/04 CES
3. Fault Confirmation
__________________
A. Test
(1) Do a BITE test with the LGCIU given in the CFDS message (Ref. AMM TASK 32-69-00-740-001).
(2) If the test gives a message that includes the DISC PROX SENSOR (37CV or 39CV), do the fault isolation procedure in (Ref. TASK 32-31-00-810-828).
(3) If the test does not give a message that includes the DISC PROX SENSOR (37CV or 39CV), but the fault continues, do the fault isolation procedure in Para. 4.
4. Fault Isolation
_______________
A. Procedure
(1) Interchange the SFCCs, use (Ref. AMM TASK 27-51-34-000-001) and (Ref. AMM TASK 27-51-34-400-001).
NOTE : This will cause each SFCC to get a new identification.
____
(2) Do an operational test of the flap interconnecting strut (Ref. AMM TASK 27-51-00-710-002).
(3) If the test is OK:
(a) Replace the SFCC-1 (21CV) or SFCC-2 (22CV) that was the source of the initial CFDS message.
(4) If the test is not OK (gives the same CFDS message as the initial CFDS message):
(a) Replace the applicable proximity sensor SENSOR-L FLAP ATTACHMENT FAILURE DETECTION (37CV) or SENSOR-L FLAP ATTACHMENT FAILURE DETECTION (39CV), (Ref. AMM TASK 27-51-15-000-002) and (Ref. AMM TASK 27-51-15-400-002).
(5) If the fault continues, do a check and repair as necessary the aircraft wiring between: 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(98)
