(1) Do the operational test of the flap system (Ref. para 3. A. (1)):
- during the test make sure that the power transfer unit is set to OFF. This is to make sure that only the flap system 2 PCU hydraulic motor operates.
- record the time necessary to extend the flaps and to retract the flaps.
(2) Do the operational test of the flap system (Ref. para 3. A. (1)):
- pressurise the Green hydraulic system for this test, (Ref. AMM TASK 29-10-00-863-001)
- during the test make sure that the power transfer unit is set to OFF. This is to make sure that only the flap system 1 hydraulic motor operates
- during the test make sure that the Yellow hydraulic system is depressurised (Ref. AMM TASK 29-10-00-864-002)
- this is to make sure that only the flap system 1 hydraulic motor operates
- record the time necessary to extend the flaps and to retract the flaps.
(3) Replace the PCU hydraulic motor on the slower system (Ref. AMM TASK 27-54-54-000-001) and (Ref. AMM TASK 27-54-54-400-001).
5. Close-up
________
A. Remove the ground support and maintenance equipment, the special and standard tools and all other items.
B. Put the aircraft back to its initial configuration.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 227
Feb 01/03R
CES R COMMAND SENSOR UNIT. CSU Out of Adjustment (Sensor out of valid region) No WTB R Set.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Possible Causes
_______________
- CSU (51CV)
- SFCC-1 (21CV)
- SFCC-2 (22CV)
- aircraft wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 27-50-00-866-008 Extension of the Flaps on the Ground
AMM 27-50-00-866-009 Retraction of the Flaps on the Ground
AMM 27-51-17-000-001 Removal of the Command Sensor Unit (CSU) (51CV)
AMM 27-51-17-400-001 Installation of the Command Sensor Unit (CSU) (51CV)
AMM 27-51-34-000-001 Removal of the SFCC (21CV,22CV)
AMM 27-51-34-400-001 Installation of the SFCC (21CV,22CV)
AMM 27-54-00-710-001 Operational Test of the Flap System
ASM 27-51/02
3. Fault Confirmation
__________________
A. SFCC System Operational Test.
(1) Move the slats and flaps control lever from and back to the initial position.
(a) Examine the UPPER ECAM and the SD FLT/CTL page to see if the fault clears.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 228
Feb 01/03 CES
(b) If the fault message clears, access FLP ON GROUND FAULTS and make sure the Ground Log is clear.
(2) Do the operational test of the flaps.(Ref. AMM TASK 27-54-00-710-001)
(a) If the ECAM warning. FLAPS FAULT is displayed.
(b) If the FLP ON GROUND FAULTS fault message: SLT/FLP CSU 51CV is displayed.
(c) Do the fault isolation.
4. Fault Isolation
_______________
A. Procedure.
(1) Set MENU MODE and go to the sub-MENU, SYSTEM DATA FLAPS.
(a) Push the line key 3L, (DICRETE INPUTS).
(b) The named SFCC trasmits the DISCRETE INPUTS page (this page is transmitted every 5 seconds).
(c) Set the flap/slat control lever (CSU LEVER) to each flap/slat position.
(d) Compare the CSU switch banks A and B:
(e) If a difference is found,(reference table 1 page block 301).
(f) Replace the defective CSU (51CV) (Ref. AMM TASK 27-51-17-000-001) (Ref. AMM TASK 27-51-17-400-001) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(92)
