B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM AMM AMM AMM AMM 27-50-00-866-008 27-50-00-866-009 27-51-34-000-001 27-51-34-400-001 27-54-53-000-001
AMM 27-54-53-000-002
AMM AMM 27-54-53-000-003 27-54-53-400-001
AMM 27-54-53-400-002
AMM ASM ASM 27-54-53-400-003 27-51/0227-51/03
3. Fault Confirmation__________________
R
R R A. Test
Extension of the Flaps on the GroundRetraction of the Flaps on the GroundRemoval of the SFCC (21CV,22CV)Installation of the SFCC (21CV,22CV)Removal of the Valve Blocks 23CV, 24CV of the Power Control Unit (Flap)Removal of the Solenoid Valves of the Power Control Unit (Flap)Removal of the Filters of the Valve BlocksInstallation of the Valve Blocks 23CV, 24CV of the Power Control Unit (Flap)Installation of the Solenoid Valves of the Power Control Unit (Flap)Installation of the Filters of the Valve Blocks
R (1) Make sure that the Post Flight Report does not show any hydraulic R system faults. R
(2) Move the flaps (Ref. AMM TASK 27-50-00-866-008) (Ref. AMM TASK 27-50-00-866-009).
R (a) Examine the SFCC, FLP ON GROUND FAULTS page for a valveblock R message. R
R (b) If a valveblock message is shown, or the A/C has had this fault R before, do the fault isolation procedure.
4. Fault Isolation
_______________
R A. Procedure
R (1) Interchange the SFCC1 and SFCC2 (Ref. AMM TASK 27-51-34-000-001) and R (Ref. AMM TASK 27-51-34-400-001).
R (2) Move the flaps, Ref. Para. 3.A. (2).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 202
Nov 01/98 CES
R (3) If the fault moves to the other system, replace the applicable SFCC-1
R (21CV) or SFCC-2 (22CV), (Ref. AMM TASK 27-51-34-000-001) and (Ref.
R AMM TASK 27-51-34-400-001).
R (4) If the fault does not move:
R - and the fault message includes the FIN 23CV or 24CV go to Para. (7)
R - and the fault message does not include the FIN 23CV or 24CV
R continue this procedure.
R (5) Do a check of the circuit resistance and circuit isolation of the
R extend and retract solenoid valves as follows:
R CAUTION: DO NOT SHORT CIRCUIT THE WIRING TO THE SOLENOID VALVES.
R DAMAGE TO THE SFCC CAN OCCUR.
R NOTE : A test is not available for the LVDT.____
R (a) Get access to the electrical connector at the applicable VALVE
R BLOCK-FLAP 1 (23CV) or VALVE BLOCK-FLAP 2 (24CV), (Ref. AMM TASK
27-54-53-000-001).
R (b) Use a Multimeter and at the connector do a check and make a note
R of the resistance values between:
R - for SFCC1/VALVE BLOCK-FLAP 1 (23CV), (EXTEND) pins T and U,
R (RETRACT) pins J and H (Ref. ASM 27-51/02)
R - For SFCC2/VALVE BLOCK-FLAP 2 (24CV), (EXTEND) pins T and U,
R (RETRACT) pins J and H (Ref. ASM 27-51/03).
R (c) The resistance values must be as follows:
R - for solenoid valves with Part No. 667C0000-02, between 71 Ohms
R and 84 Ohms.
R - for solenoid valves with Part No. 903A0000-01, between 53 Ohms
R and 60 Ohms.
R - for solenoid valves with Part No. 1106A0000-01 or 1111A0000-01,
R between 53 Ohms and 60 Ohms.
R (d) At the valveblock electrical connector, do a check for circuit
R isolation:
R 1_ For the EXTEND solenoid connect the pins U and T together.
R 2_ For the RETRACT solenoid connect the pins J and H together.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(83)
