3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the rudder servocontrols with individual hydraulic system (Ref. AMM TASK 27-24-00-710-002).
4. Fault Isolation
_______________
A. On the lower ECAM display unit, on the F/CTL page:
(1) if the pointer of the RUD indicator does not go back to the neutral position:
- do the adjustment of the rudder actuating spring rod (Ref. AMM TASK 27-24-00-820-001).
(2) if the pointer of the RUD indicator does not move to the mark (left or right):
- make sure that there is no warning related to rudder travel limitation.
B. Do the test given in para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-20-00∞∞∞∞∞∞∞∞∞∞Page 221
May 01/05 CES
YAW DAMPER ACTUATION - FAULT ISOLATION PROCEDURES
_________________________________________________
TASK 27-26-00-810-801
Failure of the Yaw Damper System
1. Possible Causes
_______________
- FAC-1 (1CC1)
- SERVO ACTR-YAW DAMPER, 1 (3CC1)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R ESPM 205550 AMM 22-66-34-000-002 Removal of the FAC (1CC1,1CC2) AMM 22-66-34-400-002 Installation of the FAC (1CC1,1CC2) AMM 27-24-00-710-002 Operational Test of the Rudder Servocontrols with
Individual Hydraulic System AMM 27-26-51-000-001 Removal of the Yaw Damper Servo Actuator (3CC1) and (3CC2) AMM 27-26-51-400-001 Installation of the Yaw Damper Servo Actuator (3CC1) and (3CC2) ASM 22-68/04 R
3. Fault Confirmation
__________________
A. Test not applicable, you cannot confirm this fault on the ground.
4. Fault Isolation
_______________
A. If the fault symptom is identified by the crew observation F/CTL - Yaw and roll jerk very hard:
(1) Remove the FAC related to the system which was active at the time of the event (Ref. AMM TASK 22-66-34-000-002).
NOTE : In normal configuration, the FAC-1 (1CC1) servoes the Green
____
yaw damper servo actuator (3CC1).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-26-00∞∞∞∞∞∞∞∞∞∞Page 201
Nov 01/04 CES
(2) At the FAC receptacle, do a check of the resistance and insulation of the LVDT of SERVO ACTR-YAW DAMPER, 1 (3CC1)(COM) between pins AB/2E and AB/2F, and between pins AB/3E and AB/3F (Ref. ASM 22-68/04).
NOTE : The resistance of the two secondary windings must be between
____ 30 Ohms and 500 Ohms. The insulation must be more than 100 Megohms.
(a) If the check is correct: 1 Replace the FAC-1 (1CC1) (Ref. AMM TASK 22-66-34-000-002) and
_ (Ref. AMM TASK 22-66-34-400-002).
2 Do a check of the wiring between the LVDT and the FAC (Ref.
_ ASM 22-68/04) for correct connections.
3 replace the SERVO ACTR-YAW DAMPER, 1 (3CC1) (Ref. AMM TASK 27-
_ 26-51-000-001) and (Ref. AMM TASK 27-26-51-400-001).
4 Do the Operational test of the rudder servocontrols with
_ individual hydraulic system (Ref. AMM TASK 27-24-00-710-002).
(b) If the check is not correct: 1 Clean the connector A of the SERVO ACTR-YAW DAMPER, 1 (3CC1)
_ R (Ref. ESPM 205550).
2 At the FAC receptacle, do again a check of the resistance and
_
insulation of the LVDT.
a If the check is correct, no further maintenance action is
_
necessary.
NOTE : After the subsequent flight, if the fault continues,
____ replace the SERVO ACTR-YAW DAMPER, 1 (3CC1) (Ref. AMM TASK 27-26-51-000-001) and (Ref. AMM TASK 27-26-51-400-001).
b If the check is not correct, see Para. (3).
_
(3) At the yaw damper, do a check of the resistance and insulation between pins A/C and A/B, and between pins A/K and A/J (Ref. ASM 22-68/04).
(a) If the check is not correct, replace the SERVO ACTR-YAW DAMPER, 1 (3CC1) (Ref. AMM TASK 27-26-51-000-001) and (Ref. AMM TASK 27-26-51-400-001)
(b) If the check is correct, repair the wiring (Ref. ASM 22-68/04).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-26-00∞∞∞∞∞∞∞∞∞∞Page 202
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(36)
