R (a) Do the operational test of the flap system (Ref. AMM TASK 27-54-R 00-710-001). R - if a permanent fault is found go to Page Block 101 and do the R applicable fault isolation procedure R - if there is no apparent fault with the flap operation, or the R operation is intermittent, do the next step.
R (b) Do the trouble shooting procedure for the applicable VALVE R BLOCK-FLAP 1 (23CV) or VALVE BLOCK-FLAP 2 (24CV), (Ref. TASK 27-R 51-00-810-802).
R NOTE : When the hydraulic motor operates, the spool of the
____ R control valve is moved and flow occurs. This flow can push R particles, in the hydraulic fluid, against the valve block R filter and cause a blockage. If a blockage occurs, the R flow decreases and the spool moves back. This movement of R the spool is sensed by the related SFCC, which stops the R applicable hydraulic motor. Flow then decreases and lets R the particles become free from the filter. This removal of R the blockage then increases the flow, which moves the R spool. This movement of the spool is sensed by the related R SFCC, which releases the applicable hydraulic motor. This R causes the flow to increase to the condition where a R blockage can occur again. This fault condition can cause R the slats to operate intermittently.
R (3) DC POWER INTERRUPT:
R - if the ECAM Warning FLAP SYS 1 (2) FAULT was shown because of a DC
R power interrupt, no more maintenance work is necessary
R - if there is no apparent DC power problem, do step (8).
R NOTE : The message DC POWER INTERRUPT is shown in the LLR when the DC
____ R power is less than 14VDC for more than 40 msec.
R (4) DC POWER BELOW 16V:
R - if the ECAM Warning FLAP SYS 1 (2) FAULT was shown because the DC
R power was less than 16.5 VDC, no more maintenance work is necessary
R - if there is no apparent DC Power problem, do step (8).
R NOTE : The message DC POWER BELOW 16V is shown in the LLR when the DC
____ R power is less than 16.5VDC, but more than 14VDC, for more than R 20 msec.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 301-399, ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 237
May 01/04 CES
R (5) SINGLE MOTOR OPERATION:
R - if the ECAM Warning FLAP SYS 1 (2) FAULT was shown because the
R flaps operated momentarily on one motor only, no more maintenance
R work is necessary
R - if there is no apparent flap motor problem, do step (8)
R - if the message LEVER OUT OF DETENT FOR MORE THAN 10 SEC is also
R shown in the LLR, do the next step.
R (6) LEVER OUT OF DETENT FOR MORE THAN 10 SEC:
R - if the ECAM Warning FLAP SYS 1 (2) FAULT was shown because the flap
R lever was sensed out of detent by one system only, do the next
R step.
R (a) Do a check of the CSU and its wiring to the SFCC, which
R identified the out of detent condition (Ref. TASK 27-51-00-810-R 805):
R NOTE : When one system senses that the flap control lever is out
____ R of detent, but the other system senses a correct R condition, then the fault is usually in the CSU.
R (7) INHIBIT SIGNAL FROM CARGO DOOR YELLOW SYSTEM. R - if the ECAM Warning FLAP SYS 2 FAULT was shown because the flap R operation was prevented by a Cargo Door fault, no more maintenance R work is necessary R - if there is no apparent Cargo Door fault, do the next step.
R NOTE : The cargo door inhibit signal is supplied by System 2 only.
____
R (a) At the MCDU set RETURN to go back to the SFCC 2 menu page.
R (b) Set CLASS 3 FAULTS FLP and do a check for the message WRONG
R INHIBIT SIGN FROM CARGO DOOR YELLOW SYSTEM:
R - if the message is shown, do the related trouble shooting
R procedure (Ref. TASK 27-51-00-810-841)
R - if the message is not shown, do the next step.
R (8) Make a record in the aircraft logbook to monitor the operation of the
R flap system during the next flight.
R **ON A/C ALL
B. Procedure
(1) If the ECAM warning FLAP SYS 1 (2) FAULT is shown, but there is no related CFDS message on the PFR, or on the SFCC 1 (2) Flap LLR, do step (2).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 238
May 01/04 CES
(2) Remove the applicable flap fault relay 91CV or 93CV and use a multimeter to do a check at the base of the holder for a ground on pin Z and 28VDC on pin X: 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(96)
