DEU-B (300RH5) connector C/8 and AAP (126RH) connector
A/8,
AAP (126RH) connector C/6 and GND (Ref. ASM 23-73/10).
R **ON A/C 106-149, 301-399, 401-499,
B. If the test confirms the fault:
- replace the AAP (126RH) (Ref. AMM TASK 23-73-13-000-001) and (Ref. AMM TASK 23-73-13-400-001).
(1) If the fault continues:
- replace the DECODER/ENCODER UNIT B (300RH7) (Ref. AMM TASK 23-73-47-000-001) and (Ref. AMM TASK 23-73-47-400-001).
(a) If the fault continues:
- do a check and repair the wiring between the: DEU-B (300RH7) connector C/40 and AAP (126RH) connector A/1, DEU-B (300RH7) connector C/41 and AAP (126RH) connector A/2, DEU-B (300RH7) connector C/24 and AAP (126RH) connector A/4, DEU-B (300RH7) connector C/39 and AAP (126RH) connector A/7, DEU-B (300RH7) connector C/23 and AAP (126RH) connector A/8, AAP (126RH) connector C/3 and GND (Ref. ASM 23-73/10).
**ON A/C 151-199,
B. If the CIDS1 BITE test gives the maintenance message ATTND PNL AFT:
- make sure that at least one cabin door is open,
- open these CBs:
49VU: 150RH (G01) COM DIR ESS/1
49VU: 157RH (G02) COM DIR ESS/2
121VU:151RH (M06) CIDS/DIR NORM/1
121VU:156RH (M07) CIDS/DIR NORM/2,
- wait for approx. 10 s and close the CBs 156RH and 157RH.
- stop for approx. 120 s,
- do the CIDS2 BITE test.
(1) If the CIDS2 BITE test does not give the message ATTND PNL AFT:
- install a new DIR-CIDS, 1 (101RH) (Ref. AMM TASK 23-73-34-400-001).
(a) If the fault continues:
- replace the ATTENDANT PANEL-AFT (126RH) (Ref. AMM TASK 23-73-13-000-001) and (Ref. AMM TASK 23-73-13-400-001).
1 If the fault continues:
_
- replace the DEU-B (300RH5) (Ref. AMM TASK 23-73-47-000-001) and (Ref. AMM TASK 23-73-47-400-001).
a If the fault continues:
_
- do a check and repair the wiring between the:
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞23-73-00∞∞∞∞∞∞∞∞∞∞Page A299
Aug 01/05 CES
DEU-B (300RH5) connector C/30 and AAP (126RH) connector
A/1,
DEU-B (300RH5) connector C/31 and AAP (126RH) connector
A/2,
DEU-B (300RH5) connector C/14 and AAP (126RH) connector
A/4,
DEU-B (300RH5) connector C/15 and AAP (126RH) connector
A/5,
DEU-B (300RH5) connector C/10 and AAP (126RH) connector
A/7,
DEU-B (300RH5) connector C/8 and AAP (126RH) connector
A/8,
AAP (126RH) connector C/6 and GND (Ref. ASM 23-73/10).
**ON A/C ALL
C. Install the removed DIR-CIDS (101RH) (Ref. AMM TASK 23-73-34-400-001).
D. Do the test given in Para. 3.A.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞23-73-00∞∞∞∞∞∞∞∞∞∞Page B200
Aug 01/05R
CES
TASK 23-73-00-810-857
CAM/ FAP - Fault in the CAM or FAP
1. Possible Causes
_______________
- DIR-CIDS, 1 (101RH)
- PROGRAMMING AND TEST PANEL (110RH)
- MODULE-CABIN ASSIGNMENT (115RH)
- FAP (120RH)
- CAM
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 23-73-00-740-005 BITE Test of the Cabin Intercommunication Data System (CIDS) through the CFDS AMM 23-73-00-740-010 Interface and Power-Up Test of the Cabin
Intercommunication Data System (CIDS) via the CFDS AMM 23-73-12-000-007 Removal of the Flight Attendant Panel (FAP) 120RH AMM 23-73-12-400-007 Installation of the Flight Attendant Panel (FAP)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 COMMUNICATIONS 通訊2(117)
