F 『
E C F M E
E E
E 56-5B E
E E
(15) and (20) and remove the harness (5).
CONFIG-1
(10) Open the 1 flip-lock clamp (30), the 3 flip-lock clamps (35), the 1 flip-lock clamp (45), and the line block (40) along station 191.
CONFIG-2
(11) Open the 2 flip-lock clamps (25), 2 flip-lock clamps (35), 1 flip-lock clamp (45), and the line block (40) along station 191.
END CONFIG-2
(12) Remove the harness (5) from the line block rubber support and the flip-lock clamps.
(13) Disconnect the electrical connector 4000EL-A from the fuel filter differential pressure switch.
(14) Disconnect the electrical connector 4003EN-A from the oil pressure transmitter.
(15) Disconnect the electrical connector 4000EN-A from the low oil pressure switch.
(16) Open the flip-lock clamp (30) and remove the harness (5).
(17) Remove the nuts (60), lockwashers (65) and washers (70) that attach the ground wires to the ground studs at station 191.
(Ref. Fig. 414/TASK 71-51-43-991-308)
WIRE GROUND
GD9951DC/1 GD9951DC
GD9951DC/2 GD9951DC
GD9952DC/1 GD9952DC
GD9952DC/2 GD9952DC
GD9953DC/1 GD9953DC
GD9953DC/2 GD9953DC
GD9954DC/1 GD9954DC
GD9954DC/2 GD9954DC
GD9955DC GD9955DC
GD9956DC GD9956DC
GD9957DC GD9957DC
F 『 EEFF : ALL E Page A45271-51-43
E E Feb 01/04 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(18) Open the line block (55) that attaches the harness to the bracket at station 167. (Ref. Fig. 414/TASK 71-51-43-991-308)
(19) Open the line blocks (40) and (50) that attach the harness (5) to the brackets at station 158.
(20) Disconnect the electrical connector 1074GK-A or 3074GD-A, as applicable, from the hydraulic pressure caution switch.
(21) Open the flip-lock clamp (30) and remove the harness (5).
(22) Remove the nuts (60), lockwashers (65), and washers (70) that attach the ground wires to the ground studs at station 158. (Ref. Fig. 414/TASK 71-51-43-991-308)
WIRE GROUND
GD9958DC/1 GD9958DC GD9958DC/2 GD9958DC GD9959DC/1 GD9959DC GD9959DC/2 GD9959DC GD9960DC/1 GD9960DC GD9960DC/2 GD9960DC GD9961DC/1 GD9961DC GD9961DC/2 GD9961DC GD9962DC/1 GD9962DC GD9962DC/2 GD9962DC GD9963DC/1 GD9963DC GD9963DC/2 GD9963DC GD9964DC GD9964DC
(23) Disconnect the electrical connector 4007EN-A from the oil chip detector. (Ref. Fig. 415/TASK 71-51-43-991-309)
(24) Disconnect the electrical connector 4002EN-A from the oil quantity transmitter.
(25) Open the line blocks (40) and (55) that attach the harness (5) to the brackets at station 199.
(26) Open the line block (40) that attaches the harness (5) to the bracket at station 191.
(27) If necessary, remove the rubber supports from the line blocks.
(28) Remove the harness (5) from the rubber supports.
F 『 EEFF : ALL E Page A45371-51-43
E E Feb 01/04 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(29) Remove the bolt (75) and the clamp (80) that attach the harness (5) to the bracket on station 199.
(30) Disconnect the electrical connector 4000KC-A from the high pressure fuel shutoff.
(31) Open the line blocks (50), (55) and the flip-lock clamp (105) along station 158.
(32) Remove the harness (5) from the line blocks (50) and (55) rubber
supports and the flip-lock clamp (105). R R AFTER SPIB NO. CFM02255MW1 R (Ref. Fig. 414/TASK 71-51-43-991-308) R
R (33) Remove the clamps and bolt (17) that attach the harness (5) to the R bracket at station 176.
R (34) Remove the clamps and bolt (22) that attach the harness (5) to the R bracket at station 185.
R (35) If neccessary, remove the rubber supports from the line block (10) R and remove the harness (5).
R (36) Open the flip-lock clamp (30) and (35) at station 191.
R (37) Remove the nuts, bolts and clamps (32) that attach the harness (5) to R the brackets at station 191.
R (38) Remove the bolt and clamp (42) and (47) that attach the harness (5) R to the brackets at station 191.
R (39) Remove the harness (5) from the flip-lock clamps.
R (40) Disconnect the electrical connector 4000EL-A from the fuel filter R differential pressure switch.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(54)
