F 『 EEFF : ALL E Page 43071-73-49
E E Feb 01/00 ERE
ECES E F 『 E C F M E E E E 56-5B E E 56-5B E E E (4) Disconnect the drain tube (20) from the CFMI supplied tube.
Fuel Servos Drain Tubes Figure 404/TASK 71-73-49-991-303
F EEFF : E ER ECES ALL 『E 71-73-49EE E Page 431 Feb 01/00
F 『
E C F M E
E E
(5) Remove the bolt (10), the nut (15) and the clamp (5) that attach the drain tube (20) to the bracket on the transfer gearbox.
(6) Remove the drain tube (20) from the engine.
(7) Put protective covers on all the tubes and fittings.
(8) Remove the container from below the drain mast.
F 『 EEFF : ALL E Page 43271-73-49
E E Feb 01/00 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 71-73-49-400-009
Installation of the Fuel Servos Drain Tubes
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
R No specific Torque Wrench : range 5.00 to 35.00 lbf.in
R (0.05 to 0.40 m.daN) No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
71-73-49-991-303 Fig. 404
3. Job Set-up
__________
Subtask 71-73-49-860-053
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
F 『 EEFF : ALL E Page 43371-73-49
E E May 01/05 E E ECES E Subtask 71-73-49-010-071
F 『
E C F M E
E E
E 56-5B E
E E
B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
4. Procedure
_________
(Ref. Fig. 404/TASK 71-73-49-991-303) Subtask 71-73-49-420-055
A. Installation of the Fireshield to Fuel Servos Drain Tube
(1) Remove the protective covers from the fireshield fitting and the drain tubes (20) and (30).
(2) Connect the drain tube (30) to the fitting on the fireshield. Do not torque the coupling nut at this time.
(3) Connect the drain tube (30) to the drain tube (20). Do not torque the coupling nut at this time.
(4) Attach the drain tube (30) to the clamp with the bolt (25), the nut
(15) and the clamp (5).
(5) Make sure that the drain tube (30) is aligned correctly on the engine.
(6) TORQUE the nut (15) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).
(7) Torque the drain tube coupling nuts. CAUTION : USE A SECOND WRENCH TO APPLY COUNTER TORQUE TO THE TUBES
_______ WHEN YOU CONNECT THE LOWER TUBES TO THE UPPER TUBES.
(a) TORQUE the drain tube (30) coupling nuts to between 200 and 250 lbf.in (2.26 and 2.82 m.daN).
F 『 EEFF : ALL E Page 43471-73-49
E E Feb 01/00 ERE
ECES E Subtask 71-73-49-420-070
F 『
E C F M E
E E
E 56-5B E
E E
B. Installation of the Fuel Servos Drain Tube
(1) Remove the protective covers from all the drain tubes.
(2) Connect the fuel servos drain tube (20) to the tube. Do not torque the coupling nut at this time.
(3) Connect the drain tube (20) to the heat exchanger drain tube. Do not torque the coupling nut at this time.
(4) Connect the drain tube (30) to the drain tube (20). Do not torque the coupling nut at this time.
(5) Attach the tube (20) to the bracket on the transfer gearbox with the clamp (5), the bolt (10) and the nut (15). 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(114)
