F 『
E C F M E
E E
E 56-5B E
E E
122VU ELEC/GCU/2 2XU2 T27
4. Procedure
_________
(Ref. Fig. 410/TASK 71-51-43-991-315)
Subtask 71-51-43-420-058
A. Installation of the Vibration Sensor Harness NOTE : For the recommended procedure for the installation of the wire
____
harness (Ref. TASK 70-60-00-910-041).
NOTE : To tighten the flip-lock clamps and line blocks, turn the captive
____ screws or captive bolts 1/4 turn clockwise to engage the cam nuts.
(1) Remove the protective covers from the electrical connectors.
(2) Put the electrical harness (5) in position on the engine.
(3) Connect the electrical connector 448VC-A to the pylon junction box.
(4) Put the harness (5) into the flip-lock clamp (25). R R BEFORE SPIB NO. CFM02255MW1 R
(5) Put the harness (5) into the rubber supports of the line blocks (10),
(15) and (20).
(6) If removed, put the rubber supports in the 3 line blocks (10) attached to the brackets at station 167.
(7) If removed, put the rubber supports in the line block (15) attached to the bracket at station 174.
(8) If removed, put the rubber supports in the 3 line blocks (20) attached to the brackets at stations 176, 185 and 191.
(9) Make sure that the harness (5) is correctly installed on the engine.
F 『 EEFF : ALL E Page A40971-51-43
E E Feb 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(10) Close the line blocks (10), (15) and (20) and tighten the captive
bolts. R R AFTER SPIB NO. CFM02255MW1 R (Ref. Fig. 410/TASK 71-51-43-991-315) R
R (11) Make sure that the harness (5) is correctly installed on the engine.
R (12) Install the clamps and bolts (12) that attach the harness (5) to the R brackets at station 167.
R (13) Install the clamps, bolt and anti-rotation lug (13) that attach the R harness (5) to the bracket at station 167.
R (14) Install the clamps and bolt (17) that attach the harness to the R bracket at station 174.
R (15) Install the clamps, bolts and anti-rotation lugs (22) that attach the R harness (5) to the brackets at station 176 and 185.
R (16) Install the clamps and bolts (23) that attach the harness (5) to the R bracket at station 191.
R (17) TORQUE the bolts (12), (13), (17), (22) and (23) to between 25 and 30 R lbf.in (0.28 and 0.33 m.daN). R R END SPIB NO. CFM02255MW1 R
R (18) Tighten the captive screw on the flip-lock clamp (25).
R (19) Connect the electrical connector 4002EV-A to the No. 1 bearing vibration accelerometer.
R (20) Examine the harness installation and make sure that all flip-lock clamps and line blocks are installed correctly.
Subtask 71-51-43-865-076
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3DA1, 3DA2, 3DA3, 4DA1, 4DA2, 4DA3, 5DA1, 5DA2, 5DA3, 1DB1, 1DB2, 4DG1, 4DG2, 1JH, 3801GX, 3802GX, 3803GX, 7TU, 2RK, 4RK FOR 1000EM1 2KS1, 4KS1, 2JH1, 3JH1, 1WE1, 2WE1, 7WD1, 8WD1, 2XU1 FOR 1000EM2
F 『 EEFF : ALL E Page A41071-51-43
E E Feb 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
2KS2, 4KS2, 2JH2, 3JH2, 1WE2, 2WE2, 7WD2, 8WD2, 2XU2
Subtask 71-51-43-861-055
C. Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002) Subtask 71-51-43-860-069
D. Do the EIS start procedure (for the lower display of the ECAM system only). (Ref. TASK 31-60-00-860-001).
Subtask 71-51-43-710-052
E. Do an operational test of the EVMU (Ref. TASK 77-32-34-710-040) .
5. Close-up
________ Subtask 71-51-43-860-070
A. Do the EIS stop procedure (Ref. TASK 31-60-00-860-002) Subtask 71-51-43-862-055
B. De-energize the aircraft circuits (Ref. TASK 24-41-00-862-002) Subtask 71-51-43-410-058
C. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the fan cowls: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(3) Remove the access platform(s).
(4) Remove the warning notice(s).
F 『 EEFF : ALL E Page A41171-51-43
E E Feb 01/04 ERE
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(44)
