Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
78-36-00-010-040 Opening of the Thrust Reverser Doors
78-36-00-410-040 Closing of the Thrust Reverser Doors
71-73-49-991-314 Fig. 415
3. Job Set-up
__________
Subtask 71-73-49-860-064
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
F 『 EEFF : ALL E Page A40571-73-49
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
Subtask 71-73-49-010-082
B. Get Access
(1) Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2) Make sure that the thrust reverser doors are open: (Ref. TASK 78-36-00-010-040) FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 71-73-49-040-051
C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
4. Procedure
_________
(Ref. Fig. 415/TASK 71-73-49-991-314)
Subtask 71-73-49-420-066
A. Installation of the Thrust Rear Frame (TRF) Drain Tube
(1) Remove the protective covers from the TFR drain nipple and the drain tube (25).
(2) Put the clamp (20) on the drain tube (25).
(3) Connect the drain tube (25) to the TFR drain nipple. Do not torque the coupling nut at this time.
NOTE : Make sure that the tube does not touch the thrust reverser or
____
the core nozzle.
F 『 EEFF : ALL E Page A40671-73-49
E E Feb 01/00 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(4) Make sure that the drain tube (25) is in the correct position on the engine.
(5) Attach the clamp (20) to the bracket with the bolt (5), the washer
(10) and the nut (15).
(6) TORQUE the nut (15) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).
(7) TORQUE the drain tube coupling nut. CAUTION : USE A SECOND WRENCH TO HOLD THE FITTINGS WHEN YOU
_______ LOOSEN/TIGHTEN THE TUBE COUPLING NUTS. THIS PREVENTS DAMAGE TO THE TUBES.
(a) TORQUE the drain tube (25) coupling nut to between 300 and 315 lbf.in (3.39 and 3.55 m.daN).
5. Close-up
________ Subtask 71-73-49-410-067
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the thrust reverser doors: (Ref. TASK 78-36-00-410-040). FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 71-73-49-440-051
B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041). Subtask 71-73-49-410-068
C. Close Access
(1) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
F 『 EEFF : ALL E Page A40771-73-49
E E Feb 01/00 E E ECES E F 『 E C F M E E E E 56-5B E E E
(2) Remove the warning notice(s).
F 『 EEFF : ALL E Page A40871-73-49
E E Feb 01/00 E E ECES E TUBES - OIL HYDRAULIC AND WATER DRAIN - INSPECTION/CHECK
F 『
E C F M E
E E
E 56-5B E
E E
________________________________________________________
TASK 71-73-49-210-001
Inspection of the Oil, Hydraulic and Water Drain Tubes/Hose
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(131)
