(5) Remove the drain manifold module (20) from the engine.

 (6) Install protective covers on the drain tubes and the module.

 F 『 EEFF : ALL E Page 40271-71-43
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Drain Manifold Module
 Figure 401/TASK 71-71-43-991-300

 F 『 EEFF : ALL E Page 40371-71-43
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 71-71-43-400-041
 Installation of the Drain Manifold Module
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific lint-free cloth
 No specific warning notice
R No specific Torque Wrench : range 5.00 to 35.00 lbf.in
R (0.05 to 0.40 m.daN) No specific Torque Wrench : range 96.00 to 900.00 lbf.in
 (1.00 to 10.00 m.daN)
 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
 71-13-00-410-040 Closing of the Fan Cowl Doors
 71-71-42-400-041 Installation of the Drain Mast
 71-71-43-991-300 Fig. 401

 3. Job Set-up
__________
 Subtask 71-71-43-860-050
 A. Aircraft Maintenance Configuration
 (1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
 F 『 EEFF : ALL E Page 40471-71-43
 E E May 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
 Subtask 71-71-43-010-052
 B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
 4. Procedure
_________
 (Ref. Fig. 401/TASK 71-71-43-991-300) Subtask 71-71-43-420-050
 A. Installation of the Drain Manifold Module
 (1) Remove the protective covers from the drain tubes and the drain manifold module (20).

 (2) Install the manifold module (20) on the engine brackets with the bolts (5), the washers (10), and the nuts (15).

 (3) TORQUE the nuts (15) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).

 (4) Connect: CAUTION : USE A SECOND WRENCH TO HOLD THE FITTINGS WHEN YOU

_______ LOOSEN/TIGHTEN THE TUBE COUPLING NUTS. THIS PREVENTS DAMAGE TO THE TUBES.
 (a) Connect the oil/hydraulic, the fuel, and the reservoir module tubes to the right side of the manifold module.

 (b) Connect the heat exchanger, the fan case, and the oil tank scupper tubes to the left side of the manifold module.

 (5) TORQUE the coupling nuts of the six drain tubes to between 300 and 315 lbf.in (3.39 and 3.55 m.daN)

 (6) Remove fluids that may have collected around the manifold module and fittings with a clean lint-free cloth.

 F 『 EEFF : ALL E Page 40571-71-43
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (7) Install the drain mast (Ref. TASK 71-71-42-400-041)

 5. Close-up
________
 Subtask 71-71-43-410-050
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (3) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 40671-71-43
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 TUBES - OIL HYDRAULIC AND WATER DRAIN - REMOVAL/INSTALLATION

____________________________________________________________
 TASK 71-73-49-000-006
 Removal of the Oil Tank Drain Tube and Hose
 1. Reason for the Job
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(105)