F 『
E C F M E
E E
E 56-5B E
E E
(10) If necessary, remove the rubber supports from the line blocks. Remove the harness (5) from the rubber supports.
CONFIG-1
(11) Open the flip-lock clamp (55) near the ignition exciter B.
CONFIG-2
(12) Open the flip-lock clamp (60) near the ignition exciter B.
END CONFIG-2
(13) Disconnect the electrical connector 4000JH2-A from the ignition exciter B.
(14) Disconnect the electrical connectors 4000KS-J2 and 4000KS-J4 from the ECU.
(15) Open the two flip-lock clamps (60) attached to the brackets at station 191. Remove the harness (5) from the clamps.
(16) Open the flip-lock clamp (80) attached to the bracket at station 191. Remove the harness (5) from the clamp.
(17) Open the two flip-lock clamps (55) attached to the brackets at station 191. Remove the harness (5) from the clamps.
(18) Disconnect the electrical connector 4000EV-C from the fan speed
sensor (N1). R R AFTER SPIB NO. CFM02255MW1 R (Ref. Fig. 408/TASK 71-51-43-991-313) R
R (19) Remove the clamps and bolts (22) that attach the harness (5) to the R brackets at station 167.
R (20) Remove the clamps, bolt and anti-rotation lug (23) that attach the R harness (5) to the brackets at station 167.
R (21) Remove the clamps, bolt and anti-rotation lug (27) that attach the R harness (5) to the brackets at station 167.
R (22) Remove the clamps and bolt (32) that attach the harness (5) to the R brackets at station 174.
F 『 EEFF : ALL E Page 48771-51-43
E E Feb 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
R (23) Remove the clamps, bolts and anti-rotation lugs (37) that attach the
R harness (5) to the brackets at station 176, 185 and 191.
R (24) Remove the bolts (40) and nuts (45) that attach the clamps (50) to
R the bracket at station 199. Remove the clamps from the harness (5).
R (25) Open the line block (25) that attaches the harness (5) to the
R bracket.
R (Ref. Fig. 409/TASK 71-51-43-991-314)
R (26) Remove the clamps and bolt (28) that attach the harness (5) to the
R bracket.
R (27) Remove the clamps and bolt (67) that attach the harness (5) to the
R bracket.
R (28) Remove the clamps, bolt and anti-rotation lug (68) that attach the
R harness (5) to the bracket.
R (29) If necessary, remove the rubber supports from the line block. Remove
R the harness (5) from the rubber support.
R (30) Remove the clamp, bolt and anti-rotation lug (57) near the ignition
R exciter B.
R (31) Disconnect the electrical connector 4000JH2-A from the ignition
R exciter B.
R (32) Disconnect the electrical connectors 4000KS-J2 and 4000KS-J4 from the
R ECU.
R (33) Remove the clamps and bolts (62) that attach the harness (5) to the
R brackets at station 191. Remove the harness (5) from the clamps.
R (34) Remove the clamp and bolt (82) that attach the harness (5) to the
R bracket at station 191. Remove the harness (5) from the clamps.
R (35) Open the flip-lock clamp (55) attached to the bracket at station 191.
R Remove the harness (5) from the clamp.
R (36) Remove the clamp and bolt (57) that attach the harness (5) to the
R brackets at station 191. Remove the harness (5) from the clamp.
F 『 EEFF : ALL E Page 48871-51-43
E E Feb 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(37) Disconnect the electrical connector 4000EV-CF from the fan speed sensor (N1).
END SPIB NO. CFM02255MW1
PRE SB RA32171-6
(38) Open the flip-lock clamp (55) attached to the bracket at station 185. Remove the harness (5) from the clamp.
POST SB RA32171-6
(39) Remove the bolt (40) that attaches the clamp (50) to the bracket at station 185. Remove the clamp (50) from the harness (5).
END SB RA32171-6
(40) Remove the bolts (70) and the nuts (75) that attach the two clamps
(50) to the starter bracket.
(41) Remove the bolt (40) and nut (45) that attach the clamp (50) to the gearbox bracket.
(42) Remove the bolt (85) and nut (90) that attach the clamp (50) and the fire detector clamp to the gearbox bracket. (SEE DETAIL C).
(43) Disconnect the electrical connector 4001EV-C from the gas generator speed sensor (N2). 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(37)
