APU Exhaust System - Component Location
Figure 001
CES EXHAUST - DESCRIPTION AND OPERATION
___________________________________
1.
General
_______ The APU exhaust system ducts the engine exhaust gas overboard. Its secondary function is to decrease the exhaust noise level. To keep aerodynamic losses during APU operation to a minimum, the duct has a sufficiently large diameter. The APU exhaust system discharge is positioned at the very aft end of the aircraft, there, a low pressure area is generated during flight. This design makes sure that exhaust gases do not re-enter the APU air intake system.
2.
System Description
__________________
(Ref. Fig. 001)
A. Muffler Assembly (Ref. 49-81-00) The forward end of the muffler assembly is attached to the APU turbine flange. The rear extends through the access fairing 317AL into the airstream. The APU compartment aft fire wall (FR 84) has a cutout for the muffler assembly. The muffler assembly is held by rails which are part of the tailcone muffler compartment.
B. Access Fairing Seal (Ref. 52-41-18) The tailcone access fairing 317AL has a cutout for the muffler assembly rear end. The gap between the access fairing and the muffler assembly is sealed with a fireproof flexible seal. This prevents exhaust gases entering the muffler compartment. This seal is permanently attached to the access fairing.
R EFF : 001-049, 101-105, 107-107, 151-199, 49-80-00Page 1 201-210, Config-2 Aug 01/05
CES
APU Exhaust System - Component Location
Figure 001
CES EXHAUST - DESCRIPTION AND OPERATION
___________________________________
1.
General
_______ The APU exhaust system ducts the engine exhaust gas overboard. Its secondary function is to decrease the exhaust noise level. To keep aerodynamic losses during APU operation to a minimum, the duct has a sufficiently large diameter. Also, the exhaust system discharge is positioned at the very aft end of the aircraft, where a low pressure area is generated during flight. Thus it is also made sure that exhaust gas does not re-enter the APU air intake system.
2.
Component Location
__________________
(Ref. Fig. 001)
-------------------------------------------------------------------------------FIN | FUNCTIONAL DESIGNATION | PANEL|ZONE|ACCESS | ATA | | | | DOOR | REF. -------------------------------------------------------------------------------
EXHAUST MUFFLER ASSEMBLY 315/ 315AL/ 49-81-41 316/ 316AR/ 317 317AL
3. System Description
__________________
A. Muffler Assembly (Ref. 49-81-00) The forward end of the muffler assembly is attached to the APU turbine flange. The rear extends through the access fairing 317AL into the airstream. The APU compartment aft fire wall (FR 84) has a cutout for the muffler assembly. The muffler assembly is held by rails which are part of the tailcone muffler compartment (Ref. 53-58-00).
B. Access Fairing Seal (Ref. 52-41-18) The tailcone access fairing 317AL has a cutout for the muffler assembly rear end. The gap between the access fairing and the muffler assembly is sealed with a fireproof flexible seal. This prevents that exhaust gas enters the muffler compartment. This seal is permanently attached to the access fairing.
APU Exhaust System - Component Location
Figure 001
CES
EXHAUST SYSTEM - DESCRIPTION AND OPERATION
__________________________________________
R **ON A/C 001-003, 051-099, 401-499,
1. General
_______ The APU exhaust system ducts the engine exhaust gas overboard. Its secondary function is to decrease the exhaust noise level. To keep aerodynamic losses during APU operation to a minimum, the duct has a sufficiently large diameter. Also, the exhaust system discharge is positioned at the very aft end of the aircraft, where a low pressure area is generated during flight. Thus it is also made sure that exhaust gas does not re-enter the APU air intake system.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER 6(26)
