(2)
 Start the APU (Ref. TASK 49-00-00-860-003).

 (3)
 Allows the APU to run 5 minutes.

 (4)
 Shutdown the APU (Ref. TASK 49-00-00-860-004).

 (5)
 Open the APU access doors 315AL, 136AR (Ref. TASK 52-41-00-010-001).

 (6)
 Do a leak check of the Oil Pump.
 NOTE : No leaks are permitted.

____
 ________

5. Close-up
 Subtask 49-91-45-410-050
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Set the LIGHT SW 11LJ to the OFF position.

 (3)
 Close the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).

 (4)
 Remove the access platform(s). Subtask 49-91-45-860-053

 B.
 Aircraft Maintenance Configuration

 (1)
 Pressurize the reservoirs of the hydraulic systems. (Ref. TASK 29-14-00-614-002).

 (2)
 De-energize the ground service network
 (Ref. TASK 24-42-00-862-001).

 (3)
 Remove the warning notice(s).

 PUMPS - OIL - REMOVAL/INSTALLATION
__________________________________
 TASK 49-91-45-000-003
 Removal of Oil Lube Module (8080KM) (131-9(A))
 WARNING : DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS
_______ WHEN YOU DO THE MAINTENANCE TASK(S).
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific container No specific warning notice No specific access platform 3.5 m (11 ft. 6 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 49-32-11-000-003 Removal of the Fuel Control Unit (FCU) (8022KM)
 (131-9(A)) 52-41-00-010-001 Open the APU Doors for Access 49-91-45-991-003 Fig. 401

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-91-45Page 401 201-210, Config-2 Aug 01/05
 CES  3. Job Set-up

__________ Subtask 49-91-45-860-055
 A. Aircraft Maintenance Configuration
 (1)
 Energize the ground service network
 (Ref. TASK 24-42-00-861-001).

 (2)
 On the panel 25VU, make sure that the APU MASTER SW p/bsw is OFF.

 (3)
 Put a warning notice in the cockpit to tell persons not to start the APU.

 (4)
 Make sure that hydraulic systems are depressurized
 (Ref. TASK 29-00-00-864-001).

 Subtask 49-91-45-865-059
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
 Subtask 49-91-45-010-053
 C. Get Access
 (1)
 Put the access platform below the APU access doors 315AL and 316AR.

 (2)
 Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001).

 (3)
 Set the LIGHT control SW 11LJ to the ON position.

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-91-45Page 402 201-210, Config-2 Aug 01/05
 CES  4. Procedure

_________
 (Ref. Fig. 401/TASK 49-91-45-991-003) Subtask 49-91-45-020-055
 A. Remove the Oil Lube Module
 (1)
 Remove the fuel control unit (Ref. TASK 49-32-11-000-003).

 (2)
 Put the container below the oil lube module (4).

 (3)
 Disconnect the electrical connectors (3).

 (4)
 Put blanking caps on the disconnected electrical connectors.

 (5)
 Loosen the captive bolts (1) and remove the oil lube module (4) from the APU.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER 6(136)