(2)
 Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001)

 (3)
 Set the LIGHT SW 11LJ to the ON position.

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-94-15Page 402 201-210, Aug 01/05
 CES  4. Procedure

_________
 (Ref. Fig. 401/TASK 49-94-15-991-001) Subtask 49-94-15-020-050
 A. Removal of the Oil Temperature Sensor
 (1)
 Put the container in position below the gearbox.

 (2)
 Disconnect the electrical connector (1).

 (3)
 Put blanking caps on the disconnected electrical connectors.

 (4)
 Remove the oil temperature-sensor (2).

 (5)
 Install a blanking plug in the gearbox port.

 (6)
 Remove and discard the O-ring (3) from the oil temperature sensor (2).

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-94-15Page 403 201-210, Aug 01/05
 CES

 Oil Temperature Sensor Figure 401/TASK 49-94-15-991-001 
R  EFF : 001-049, 101-105, 107-107, 151-199, 201-210,  49-94-15 Page 404 Aug 01/05
 CES 

 TASK 49-94-15-400-001
 Installation of Oil Temperature Sensor (8092KM) (131-9(A))

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 8.0 l (2.1133 USgal)
 No specific Torque Wrench : range 36.00 to 220.00 lbf.in

 (0.40 to 2.60 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 03-002  GB DEF-STAN 91-101 LUBRICATING OIL TURBINE ENGINE SYNT BASE (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
O-ring  49-91-09 02 -230

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-94-15Page 405 201-210, Aug 01/05
 CES

 D. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through the Ground Connector 31-32-00-860-001 Procedure to Get Access to the SYSTEM REPORT/TEST
 Menu Page 49-00-00-860-008 APU Start by External Power (131-9(A)) 49-00-00-860-009 APU Shutdown by External Power (131-9(A)) 49-90-00-600-007 Check and Replenish Oil Level (131-9(A)) 52-41-00-010-001 Open the APU Doors for Access 52-41-00-410-001 Close the APU Doors after Access 49-94-15-991-001 Fig. 401
 3. Job Set-up
__________
 Subtask 49-94-15-860-051
 A. Aircraft Maintenance Configuration
 (1)
 Energize the ground service network
 (Ref. TASK 24-42-00-861-001).

 (2)
 On the panel 25VU make sure that the APU MASTER SW p/bsw is OFF.

 (3)
 Make sure that there is a warning notice in the cockpit to tell persons not to start the APU.

 (4)
 Make sure that hydraulic systems are depressurized
 (Ref. TASK 29-00-00-864-001).

 (5)
 Make sure that the APU access doors are open (Ref. TASK 52-41-00-010-001).

 (6)
 Make sure that the access platform is in position below the APU compartment.

 (7)
 Make sure that the LIGHT SW 11LJ is set to the ON position.

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-94-15Page 406 201-210, Aug 01/05
 CES

 (8)
 Make sure that the container is in position below the gearbox. Subtask 49-94-15-865-051

 B.
 Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER 6(184)