(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
1EFF : ALL 1 32-33-13Page 411 1 1 Feb 01/05R 1 1 1CES 1
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ R THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING AND RUBBER GLOVES.
(a) Apply SPECIAL MATERIALS (Material No. 05-002) to the bolts (9) and the component interface.
4. Procedure
_________
(Ref. Fig. 401/TASK 32-33-13-991-001)
Subtask 32-33-13-420-052
A. Installation of the MLG Vent Valve 2516GM
(1)
Put the vent valve (12) in position and install the bolts (9) and the nuts (11).
(2)
Remove the blanking plugs.
(3)
Connect the connectors (3), (8) and (10) to the unions (4) and (7).
(4)
TORQUE the connection (3) to between 2.9 and 3.2 m.daN (21.38 and
23.59 lbf.ft).
(5)
TORQUE the connections (8) and (10) to between 5.4 and 5.9 m.daN
(39.82 and 43.51 lbf.ft).
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(6) Mark the connections with PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-010).
1EFF : ALL 1 32-33-13Page 412 1 1 Feb 01/05 1 1 1CES 1 Subtask 32-33-13-480-050
B. Put the rigging pins in position.
(Ref. Fig. 402/TASK 32-33-13-991-002)
(1)
Put the RIGGING PIN (98DNSA20208060) through the lever into the forward face of the MLG door uplock 2521GM.
(2)
Put the RIGGING PIN (98DNSA20208040) through the lever into the forward face of the MLG vent valve 2516GM.
Subtask 32-33-13-820-050
C. Put the adjustable rod (1) between the forks of the lever (17) and make sure that the holes are aligned. If it is necessary, adjust the rod (1) at both ends.
WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE. CUT,
_______ REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Remove and discard the lockwire from the locknuts (2).
(2)
Loosen the locknuts (2).
(3)
Turn the rod (1) until the holes are aligned.
(4)
Tighten the locknuts (2).
(5)
Make sure that the threads of the rod ends are in safety.
(6)
Safety the locknuts (2) with corrosion-resistant steel lockwire 0.8 mm (0.032 in.) dia.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
1EFF : ALL 1 32-33-13Page 413 1 1 Feb 01/05R 1 1 1CES 1
Rigging of the MLG Vent Valve 2516GM Figure 402/TASK 32-33-13-991-002
1EFF : 1 1R 1CES ALL 1 11 1 32-33-13 Page 414 Feb 01/05
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ R THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING AND RUBBER GLOVES.
(a)
Apply SPECIAL MATERIALS (Material No. 05-002) to the bolt (22), the bush (21) and the washer (20).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(9)
