(6)
TORQUE the connectors (19) to between 2.9 and 3.2 m.daN (21.38 and
23.59 lbf.ft).
(7)
TORQUE the connectors (2) and (5) to between 9.7 and 10.7 m.daN
(71.53 and 78.90 lbf.ft). R (8) Mark the connections with PAINTS FOR DETAIL (INTERNAL AND EXTERN AL)
R (Material No. 07-010). Subtask 32-33-12-480-050
B. Put the rigging pins in position.
(Ref. Fig. 402/TASK 32-33-12-991-002)
(1)
Put the RIGGING PIN (98DNSA20208060) into the lever and the forward face of the MLG door uplock 2520GM.
(2)
Put the RIGGING PIN (98DNSA20208060) through the rigging hole and into the cutout valve (3).
Subtask 32-33-12-820-050
C. Adjustment
(1)
Put the adjustable rod (7) between the forks of the lever (9). If the holes are not aligned, adjust the rod (7).
(2)
Remove and discard the lockwire from the locknuts (8).
(3)
Loosen the locknuts (8).
(4)
Turn the rod (7) until the eye-end is aligned with the holes in the forks of the lever (9).
(5)
Make sure that the threads are in safety.
(6)
Tighten and safety the locknuts (8) with corrosion-resistant steel lockwire 0.8 mm (0.032 in.) dia.
1EFF : ALL 1 32-33-12Page 411 1 1 May 01/99 1 1 1CES 1
Rigging of the L/G Free-Fall Cutout-Valve 2515GM
Figure 402/TASK 32-33-12-991-002
1EFF : ALL 1 32-33-12 Page 412
1 1 Feb 01/98
1 1
1CES 1
Subtask 32-33-12-560-052
D. Installation of the Rod (7)
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
(1)
Apply SPECIAL MATERIALS (Material No. 05-002) to the bolt (18), the bush (17) and the washer (16).
(2)
Put the rod (7) in position.
(3)
Install the bush (17), the bolt (18), the washer (16) and the nut (15).
(4)
Safety the nut (15) with the new cotter pin (13).
Subtask 32-33-12-080-050
E. Remove the Rigging Pins
(1)
Remove the rigging pin from the cutout valve (3) and the lever (9).
(2)
Remove the rigging pin from the uplock assembly 2520GM.
Subtask 32-33-12-865-052
F. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GA, 2GA, 52GA, 1701GK, 1702GK.
1EFF : ALL 1 32-33-12Page 413 1 1 Feb 01/98 1 1 1CES 1 Subtask 32-33-12-860-052
G. Preparation for Test
(1)
Connect the PTU isolation coupling (Ref. TASK 29-23-00-860-002).
(2)
If the flight configuration precautions were obeyed, put the aircraft back to the serviceable condition (Ref. TASK 32-00-00-860-002).
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the container.
(6)
Make sure that the work area is clean and clear of tool(s) and other items.
(7)
Close the right MLG door (Ref. TASK 32-12-00-410-001).
(8)
If necessary fill the reservoir of the Green hydraulic system to the correct level (Ref. TASK 12-12-29-611-001).
Subtask 32-33-12-720-050
H. Functional Test
(1)
Do a functional test of the normal extension and retraction of the landing gear (Ref. TASK 32-31-00-720-002).
(2)
Do a functional test of the free-fall extension system (Ref. TASK 32-33-00-720-001).
(3)
Open the right MLG door (Ref. TASK 32-12-00-010-001).
(4)
Make sure that there is no hydraulic fluid leakage from the cutout valve 2515GM.
1EFF : ALL 1 32-33-12Page 414 1 1 Feb 01/98 1 1 1CES 1
5. Close-up
________ Subtask 32-33-12-410-051
A. Close Access
(1)
Apply corrosion protection to the bolt heads, pipe connections and the adjacent areas (Ref. TASK 51-75-13-916-002).
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM LANDING GEAR 起落架6(5)
