4. Procedure
_________ R **ON A/C 001-049, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 401/TASK 32-41-12-991-001)
**ON A/C 051-099,
(Ref. Fig. 401A/TASK 32-41-12-991-001-A) R **ON A/C 001-049, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 32-41-12-010-051
A. Get access
(1)
Cut and remove the corrosion resistant steel lockwire.
(2)
Remove the screws (7) and the washers (8).
(3) Remove the hubcap (6).
Subtask 32-41-12-020-050
B. Removal of the NLG wheel
(1)
Remove and discard the two cotter pins (4).
(2)
Remove the nuts (3), the washers (2) and the bolts (5).
(3)
Remove the casing (9).
(4)
Remove the axle nut (10) with the ADAPTOR NLG (J47549).
(5)
Install the PROTECTOR NLG (J47548).
(6)
Remove the wheel.
1EFF : ALL 1 32-41-12Page 403 1 1 Aug 01/05 1 1 1CES 1
Nose Gear Wheel
Figure 401/TASK 32-41-12-991-001
R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-12Page 404 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R Nose Gear Wheel
R Figure 401A/TASK 32-41-12-991-001-A
R 1EFF : 051-099, 1 32-41-12 Page 405
1 1 May 01/05
1 1
1CES 1
R **ON A/C 051-099,
R Subtask 32-41-12-010-051-A
R A. Get access
R (1) Cut and remove the corrosion resistant steel lockwire.
R (2) Remove the screws (14) and the washers (15).
R (3) Release the grommet (16) and remove the hubcap (12).
R (4) Disconnect the electrical connector (11) from the connector (18) and
R install the blanking cap on the disconnectd connector.
R WARNING : MAKE SURE THAT THE TIRE IS FULLY DEFLATED._______
R (5) Remove and discard the cotter pin (5). Remove the nut (6).
R (6) Remove the pressure transducer (4).
R (7) Remove the preformed packings (3) and discard them.
R Subtask 32-41-12-020-050-A
R B. Removal of the NLG Wheel
R (1) Remove and discard the two cotter pins (9).
R (2) Remove the nuts (8), the washers (7) and the bolts (10).
R (3) Remove the axle nut (17) with the ADAPTOR NLG (J47549).
R (4) Install the PROTECTOR NLG (J47548).
R (5) Remove the wheel.
R 1EFF : 051-099, 1 32-41-12Page 406 1 1 May 01/05 1 1 1CES 1
R **ON A/C ALL
TASK 32-41-12-400-001
Installation of the NLG Wheel (2659GM,2660GM)
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft) No specific Torque Wrench : range 6.00 to 36.00 m.daN
(50.00 to 260.00 lbf.ft) J47549 1 ADAPTOR NLG
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
No specific corrosion resistant steel lockwire 0.8mm (0.032 in) dia
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 04-035
SYNTHETIC WHEEL BEARING GREASE (Ref. 20-31-00)
Material No. 11-002 USA MIL-PRF-680
DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
(Ref. 20-31-00)
1EFF : ALL 1 32-41-12Page 407 1 1 May 01/05 1 1 1CES 1 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM LANDING GEAR 起落架6(78)
