32-33-00-720-001 Functional Test of the Free-Fall Extension 32-33-00-820-003 Adjustment of the MLG Free-Fall Extension Cable
System 32-33-16-991-001 Location of the Rigging Pins 53-32-12-400-002 Installation of the Cabin Floor Panels 32-33-17-991-001 Fig. 401
3. Job Set-up
__________
Subtask 32-33-17-941-051
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-
Make sure that the landing-gear control-lever 6GA is in the DOWN position.
-
Make sure that the warning notice is in position to tell persons not to operate the landing gear.
(4)
On the panel 110VU, make sure that the GRAVITY GEAR EXTN handle is folded into the center console.
Subtask 32-33-17-860-050
B. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized from the external power (Ref. TASK 24-42-00-861-001).
(2)
Make sure that the MLG doors are opened (Ref. TASK 32-12-00-010-001).
(3)
Make sure that the GROUND LOCK SLEEVE (460005835) is on the applicable main gear door actuator.
1EFF : ALL 1 32-33-17Page 407 1 1 Feb 01/98 1 1 1CES 1 Subtask 32-33-17-865-050
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
R 49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
4. Procedure
_________
(Ref. Fig. 401/TASK 32-33-17-991-001)
Subtask 32-33-17-420-050
A. Installation of the Torque Tube Assembly
(1)
Do an inspection of the component interface and/or the adjacent area.
(2)
Make sure that the surfaces of the flange (13) and the brackets (14) and (18) are in a good condition.
(3)
Put the torque tube assembly (21) in position.
(4)
Install the bolts (20) and the nuts (19).
(5)
View D:
(a) Install the bolts (12) and the nuts (15).
(6)
View C and E:
(a)
Put the control rods (5) and (16) in postion.
(b)
Install the bushes (8) the bolts (7) the washers (9) and the castellated nuts (10).
(c)
Safety the castellated nuts (10) with the cotter pins (11).
1EFF : ALL 1 32-33-17Page 408 1 1 Feb 01/99 1 1 1CES 1 Subtask 32-33-17-480-051
B. Installation of the Rigging Pins (Ref. TASK 32-33-16-991-001)
(1)
For the pulley at frame 47:
(Ref. Fig. 401/TASK 32-33-17-991-001)
-Put a RIGGING PIN (98DNSA20208150) in the position Pin 2.
(2)
For the MLG free-fall extension cables:
(Ref. Fig. 401/TASK 32-33-17-991-001)
-Put a RIGGING PIN (98DNSA20208060) in the applicable position Pin
3. Subtask 32-33-17-820-050
C. Install the MLG Free-Fall Extension Cables (1) and (2)
(Ref. Fig. 401/TASK 32-33-17-991-001)
(1)
Put the free-fall extension cables (1) and (2) in position at the torque tube assembly (21).
(2)
Connect each cable to its related cable with the turnbuckles (4).
(3)
Temporarily attach the locking pins (3).
(4)
Adjust the free-fall extension cables that were loosened (Ref. TASK 32-33-00-820-003).
(5)
Do a cable tension check on the free-fall extension cables that were loosened (Ref. TASK 32-33-00-200-001).
Subtask 32-33-17-865-051
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GA, 2GA, 52GA.
Subtask 32-33-17-720-050
E. Test
(1)
Make sure that all the rigging pins are removed.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(32)
