1EFF : ALL 1 31-60-00Page 535 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
8.
Push the line key adjacent to the EIS1 (2) indication.
9.
Push the line key adjacent to the TEST indication.
10.
Push the line key adjacent to the SYSTEM TEST RESULT indication.
11.
On the MCDU, push the line key adjacent to the RETURN indication until the CFDS MENU page comes into view.
R **ON A/C 401-499,
Subtask 31-60-00-740-051-A
A. System test of the DMC
On the MCDU:
-the EIS DMC1 (2) page comes into
view. On the display units:
-make sure that the CAPT (F/O) PFD and ND and the upper (lower) ECAM DU operate in the maintenance mode.
On the MCDU:
-
the EIS DMC1 (2) TEST page comes into view.
-
the TEST OK indication comes intoview.
On the display units:
-
the CAPT (F/O) PFD and ND and theupper (lower) ECAM DU go back to thenormal mode.
NOTE : This test is for the DMC1. For DMC2 and the DMC3, use the
____
indications between the parentheses.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the MCDU: - the DMC1 (DMC2, DMC3) main menu page
-push the line key adjacent to the comes into view. A green message
EIS 1 (EIS 2), (EIS 3) indication MAINTENANCE MODE comes into view on the CAPT PFD, ND, EWD and SD (F/O PFD, ND with the DMC2), (no cockpit effect with the DMC3)
1EFF : ALL 1 31-60-00Page 536 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
-push the line key adjacent to the SYSTEM TEST indication
- obey the instructions such as: SET ADIRU...ENTER PPOS...and press the arrow line key
- obey the instructions such as: MAKE SURE THAT ALL DU...
-push the line key adjacent to the START TEST indication
-press the relative line key and obey the instructions
-
the DMC1 (DMC2, DMC3) SYSTEM TESTpage 1/2 comes into view with initial conditions
-
the DMC 1 (DMC2, DMC3) SYSTEM TESTpage 2/2 comes into view
-
the TEST IN PROGRESS 45s indicationcomes into view
-On the MCDU, DMC 1 (DMC 2, DMC 3)SYSTEM TEST comes into view
-make sure that the display test comes into view on the CAPT PFD, ND, EWD and SD (F/O PFD and ND with the DMC2), (no cockpit effect with the DMC3)
-TEST OK comes into view
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
Subtask 31-60-00-740-052
B. DMC3 Test
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the panel 8VU:
-set the EIS DMC selector switch from NORM to CAPT/3.
2. On the MCDU:
-push the line key adjacent to the INST indication.
3. Push the line key adjacent to the EIS3 indication.
On the MCDU:
-
the SYSTEM REPORT/TEST INST pagecomes into view.
-
the EIS DMC3 page comes into view.On the EFIS/ECAM display units:
R 1EFF : ALL 1 31-60-00Page 537 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
4.
Push the line key adjacent to the TEST indication.
5.
Push the line key adjacent to the SYSTEM TEST indication.
6.
Push the line key adjacent to the RETURN indication.
7.
Push the line key adjacent to the START TEST indication.
8.
Push the line key adjacent to the RETURN indication until the SYSTEM REPORT/TEST INST page comes into view.
9.
Push the line key adjacent to the EIS3 indication.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 7(87)
