3.
 On the MCDU:

-
push the line key adjacent to the EIS3 indication.

-
push the line key adjacent to the TEST indication

-
push the line key adjacent to the I/P TEST indication.

-Push the line key adjacent to the RETURN indication until the CFDS MENU page comes into view.
 4. On the panel 8VU, set the EIS DMC selector switch to NORM.
-
the I/P TEST IN PROGRESS indicationcomes into view; then the I/P TEST RESULTS and the NO BUS FAULT (or TCAS warning message if TCAS is not installed) indications come into view.

-
the CAPT (F/O) PFD and ND and theupper (lower) ECAM DU go back to thenormal mode.

-make sure that:
* the CAPT PFD and ND and the upperECAM DU operate in the maintenance mode (MAINTENANCE MODE comes into view on these 3 display units) * on the MCDU, the EIS DMC3 page comes into view.
- on the MCDU, the EIS DMC3 TEST pagecomes into view.
-
the I/P TEST IN PROGRESS indicationcomes into view; then the I/P TEST RESULTS and the NO BUS FAULT (or TCAS warning message if TCAS is not installed) indications come into view.

-
the CAPT PFD and ND and the upperECAM DU go back to the normal mode.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 31-60-00Page 532 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 5. Close-up
________ Subtask 31-60-00-860-060
 A. Put the aircraft back to its initial configuration.
 (1)
 Do the EIS Stop Procedure (Ref. TASK 31-60-00-860-002)

 (2)
 On the maintenance panel 50VU, press the ENG/FADEC GND PWR 1 & 2 pushbutton switches (the ON legend goes off).

 (3)
 Do the ADIRS Stop Procedure (Ref. TASK 34-10-00-860-005).

 (4)
 On the radar control unit, set the control switches back to their initial position.

 (5)
 On the ATC control unit, set the control switches back to their initial position.

 (6)
 De-energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-862-002)

 (7)
 Make sure that the work area is clean and clear of tool(s) and other items.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 31-60-00Page 533 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL

 TASK 31-60-00-740-004 EIS System Test WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______ YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
 1. Reason for the Job__________________ Self Explanatory
 2. Job Set-up Information______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
24-41-00-861-002  Energize the Aircraft Electrical Circuits from the External Power
 24-41-00-862-002  De-energize the Aircraft Electrical Circuits Supplied from the External Power
 31-32-00-860-008  Procedure to Get Access to the SYSTEM
 REPORT/TEST/INST Page 31-60-00-860-001 EIS Start Procedure 31-60-00-860-002 EIS Stop Procedure
 3. Job Set-up
__________ Subtask 31-60-00-860-062
 A. Aircraft Maintenance Configuration
 (1)
 Energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-861-002)

 (2)
 Do the EIS start procedure (Ref. TASK 31-60-00-860-001)

 (3)
 On one MCDU, get the SYSTEM REPORT/TEST INST menu page (Ref. TASK 31-32-00-860-008)

 1EFF : ALL 1 31-60-00Page 534 1 1 Aug 01/05R 1 1 1CES 1

 4. Procedure
_________

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,

 Subtask 31-60-00-740-051
 A. DMC1 or DMC2 Test
 NOTE : This test is for the DMC1. For the DMC2 use the indications

____
 between parentheses.

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:  On the MCDU:
 2. Push the line key adjacent to the EIS1 (2) indication.  - the EIS DMC1 (2) page comes intoview. On the EFIS/ECAM display units: - make sure that the CAPT (F/O) PFD and ND and the upper (lower) ECAM DU operate in the maintenance mode (MAINTENANCE MODE comes into view on these three display units).
 3. Push the line key adjacent to the TEST indication.  On the MCDU:- the EIS DMC1 (2) TEST page comes into view.
 4. Push the line key adjacent to the SYSTEM TEST indication.  - the EIS DMC1 (2) SYSTEM TEST pagecomes into view.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 7(86)