(2)
Put the warning notice(s) in position to tell persons not to pressurize the Blue hydraulic system:
-in the cockpit on the hydraulic section 40VU of the overhead panel, - on the ground service panel of the Blue hydraulic system.
Subtask 29-22-51-860-054
B. Aircraft Maintenance Configuration
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
(1)
Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).
(2)
Make sure that the Blue hydraulic system is depressurized and put it in the maintenance configuration. (Ref. TASK 29-00-00-864-001).
(3)
Depressurize the reservoir of the Blue hydraulic system (Ref. TASK 29-14-00-614-001).
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 402 1 1 Config-1 May 01/05 1 1 1CES 1 Subtask 29-22-51-010-052
C. Get Access
(1)
Open the left main gear main door (Ref. TASK 32-12-00-010-001).
(2)
Open the access door 195BB.
(3)
Remove the access panel 147BB.
(4)
Remove the access panel 147CB.
Subtask 29-22-51-869-050
D.
Extend the ram air turbine (RAT) (Ref. TASK 29-22-00-869-001).
Subtask 29-22-51-010-053
E.
Get Access
(1) Remove the screws (7),(6) and the washers (5) from the sidewall panel (8). (Ref. Fig. 401/TASK 29-22-51-991-001)
(2)
Remove the sidewall panel (8) from the structure (9).
Subtask 29-22-51-865-053
F.
Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------106VU CSM/G /EV/MAN/SPLY 6XE B04 121VU HYDRAULIC/RAT/SPLY/EXTN/SOL1 2803GE P33
R **ON A/C 001-049, 051-061, 101-102, 201-202,
121VU HYDRAULIC/RAT/CTL 2801GE P32 R **ON A/C 103-105, 203-203,
121VU HYD/RAT/CTL 2801GE P32
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 403 1 1 Config-1 May 01/05 1 1 1CES 1
Ram Air Turbine (Sheet 1)
Figure 401/TASK 29-22-51-991-001
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 404 1 1 Config-1 May 01/05 1 1 1CES 1R **ON A/C 001-049, 051-061, 101-105, 201-203,
4. Procedure
_________
(Ref. Fig. 402/TASK 29-22-51-991-003, 403/TASK 29-22-51-991-004)
Subtask 29-22-51-020-052
A. Removal of the Ram Air Turbine CAUTION : USE A SECOND WRENCH TO APPLY COUNTERTORQUE TO THE UNION WHEN
_______ YOU DISCONNECT/CONNECT HYDRAULIC LINES ON UNIONS. IF YOU USE THE SECOND WRENCH, YOU WILL NOT LOOSEN OR TIGHTEN THE UNION TOO MUCH.
(1)
Disconnect the electrical connectors (42),(43).
(2)
Put blanking caps on the disconnected electrical connectors.
(3)
Put blanking caps on the electrical receptacles.
(4)
Remove the screw (3), the washer (2) and the p-clips (1).
(5)
Remove and discard the cotter pins (16).
(6)
Support the RAT.
(7)
Remove the nut (25), the washers (26), the two bushes (27) and the bolt (30) from the door link (28).
(8)
Remove the door link (28) from the distance fork (29).
(9)
Remove the distance fork (29).
(10)
Remove the nut (17), the washers (18), the two bushes (19),(21) and the bolt (23).
(11)
Remove the door link (20) from the swivel pin (22).
(12)
Remove the swivel pin (22) and the shim washer (70).
(13)
Support the RAT door 195CB.
(14)
Remove the nut (15), the washers (11) and the bolt (10) from the piston rod eye-end (13).
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 405 1 1 Config-1 May 01/05 1 1 1CES 1
Ram Air Turbine (Sheet 2)
Figure 402/TASK 29-22-51-991-003
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 406 1 1 Config-1 May 01/05 1 1 1CES 1 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓6(7)
