C. Expendable Parts -------------------------------------------------------------------------------
FIG.ITEM --------- |DESIGNATION ---------------------------------------- |IPC-CSN------------------------------
7 O-ring 29-22-51 01 -240
9 shim 29-22-51 01 -220
10 O-ring 29-22-51 01 -210
D. Referenced Information
------------------REFERENCE -------------------------------DESIGNATION ------------------------------
-------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic Service Cart 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-00-00-910-002 Safety Procedures of the Hydraulic System 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
Power Supply 29-10-00-864-003 Depressurize the Blue Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
the Ground Connector 29-22-00-869-001 Extension of the Ram Air Turbine (RAT) on the Ground 29-22-00-869-002 Retraction of the Ram Air Turbine (RAT) on the Ground 29-22-51-991-007 Fig. 407
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 467 1 1 Config-1 Aug 01/05R 1 1 1CES 1
3. Job Set-up
__________ Subtask 29-22-51-865-065
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------106VU CSM/G /EV/MAN/SPLY 6XE B04 121VU HYDRAULIC/RAT/SPLY/EXTN/SOL1 2803GE P33
**ON A/C 001-049, 051-061, 101-102, 201-202,
121VU HYDRAULIC/RAT/CTL 2801GE P32 **ON A/C 103-105, 203-203,
121VU HYD/RAT/CTL 2801GE P32 **ON A/C 001-049, 051-061, 101-105, 201-203,
Subtask 29-22-51-860-064
B. Aircraft Maintenance Configuration
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
(1)
Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).
(2)
Make sure that the Blue hydraulic system is depressurized and put it in the maintenance configuration (Ref. TASK 29-00-00-864-001).
(3)
Make sure that the reservoir of the Blue hydraulic system is depressurized (Ref. TASK 29-14-00-614-001).
(4)
Make sure that the warning notices are in position to tell persons not to pressurize the Blue hydraulic system:
-in the cockpit on the hydraulic section 40VU of the overhead panel, - on the ground service panel of the Blue hydraulic system.
(5)
Make sure that the safety barriers are in position.
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 468 1 1 Config-1 Aug 01/05R 1 1 1CES 1
(6)
Make sure that the RAT is extended (Ref. TASK 29-22-00-869-001).
(7)
Make sure that the container is in position below the RAT.
4. Procedure
_________
(Ref. Fig. 407/TASK 29-22-51-991-007) Subtask 29-22-51-560-050
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Remove the blanking plug from the port (6). NOTE : Calculate the necessary thickness of the shim to give the
____
correct end float for the filter.
(4)
Measure the depth from the bottom of the filter housing (13) to the mating surface of the port (6). Write down this measurement as dimension 'A'.
(5)
Put the filter (8) with its closed end in the filter plug (11). Do not put the shim in the filter plug (11) at this time.
(6)
Make sure that the closed end of the filter has contact with the bottom of the filter plug (11).
(7)
Measure the distance between the end of the filter (8) and the mating face (12) of the filter plug (11). Write down this measurement as dimension 'B'.
(8)
Remove the filter (8) from the filter plug (11).
(9)
Make sure that the thickness of the shim (9) is such that the dimension 'B' is between 0.08 mm (0.0031 in.) and 0.20 mm (0.0078 in.) less than the dimension 'A'. If the dimension is correct without the shim (9), it is not necessary to install the shim.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓6(26)
