-in the cockpit on the hydraulic section 40VU of the overhead panel, - on the ground service panel of the Blue hydraulic system.
(5)
Make sure that the safety barriers are in position.
(6)
Make sure that the RAT is extended (Ref. TASK 29-22-00-869-001).
(7)
Make sure that the container is in position below the RAT. Subtask 29-22-51-865-062
B.
Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------106VU CSM/G /EV/MAN/SPLY 6XE B04 121VU HYDRAULIC/RAT/SPLY/EXTN/SOL1 2803GE P33
**ON A/C 001-049, 051-061, 101-102, 201-202,
121VU HYDRAULIC/RAT/CTL 2801GE P32 **ON A/C 103-105, 203-203,
121VU HYD/RAT/CTL 2801GE P32 **ON A/C 001-049, 051-061, 101-105, 201-203,
4. Procedure
_________
(Ref. Fig. 407/TASK 29-22-51-991-007) Subtask 29-22-51-210-060
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 460 1 1 Config-1 Aug 01/05R 1 1 1CES 1
Subtask 29-22-51-420-055
B. Installation of the Clogging Indicator
(1)
Put a new back-up ring (3) on the clogging indicator (4).
(2)
Lubricate the new O-rings (2) with HYDRAULIC FLUIDS (Material No. 02-003).
(3)
Put the new O-rings (2) on the clogging indicator (4).
(4)
Lubricate the threads of the clogging indicator (4) with HYDRAULIC FLUIDS (Material No. 02-003).
(5)
Remove the blanking plug from the port (1).
(6)
Carefully install the clogging indicator (4) in the port (1).
(7)
Torque the nut (5) to between 1.08 and 1.36 m.daN (95.57 and 120.35 lbf.in).
(8)
Safety the nut (5) with lockwire, corrosion-resistant steel dia 0.8 mm (0.0315 in.).
Subtask 29-22-51-865-063
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6XE, 2801GE, 2803GE.
Subtask 29-22-51-790-050
D. Test
(1)
Make sure that the level of the fluid in the reservoir of the Blue hydraulic system is correct. Add fluid as necessary (Ref. TASK 12-12-29-611-001) or (Ref. TASK 12-12-29-611-002).
(2)
Pressurize the reservoir of the Blue hydraulic system (Ref. TASK 29-14-00-614-002).
(3)
Pressurize the Blue hydraulic system (Ref. TASK 29-10-00-863-003).
(4)
Examine the clogging indicator and make sure that there are no leaks.
(5)
Make sure that the clogging indicator does not show a blocked filter.
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 461 1 1 Config-1 Aug 01/05R 1 1 1CES 1
Subtask 29-22-51-942-059
E. Put the aircraft back to the serviceable condition.
(1)
Remove the container from below the RAT.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 29-22-51-869-055
F. Retract the RAT (Ref. TASK 29-22-00-869-002). Subtask 29-22-51-942-060
G. Remove the warning notice(s). Subtask 29-22-51-864-059
H. Depressurize the Blue hydraulic system (Ref. TASK 29-10-00-864-003).
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 462 1 1 Config-1 Aug 01/05R 1 1 1CES 1
TASK 29-22-51-000-004 Removal of the Filter WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______ CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : MAKE SURE THAT THE RAT TRAVEL RANGE IS CLEAR BEFORE YOU
_______ EXTEND/RETRACT THE RAT.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job__________________ Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓6(24)
