(2)
Clean the component interfaces and the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004).
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Do an inspection of the component interface and/or the adjacent area.
Subtask 29-13-52-420-052
C. Installation of the Engine Pump Fire-Valve
(1)
Put the engine pump fire-valve (5) in position.
(2)
Engage the coupling nut (4). Do not tighten it fully.
(3)
Extend the compensated slide (6) to engage the coupling nut (1). Do not tighten it fully.
(4)
Make sure that the engine pump fire-valve (5) is correctly aligned, and tighten the coupling nuts (1) and (4).
(5)
Connect the cable connector (3) to the electrical connector (2). Subtask 29-13-52-865-052
D.
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3700GD, 3702GD.
Subtask 29-13-52-863-050
E. Pressurize the Applicable Hydraulic System WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES
_______ ARE CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
(1)
Pressurize the Yellow hydraulic system (Ref. TASK 29-10-00-863-002). Subtask 29-13-52-720-051
F.
Test
(1)
Do a functional test of the engine pump fire-valve (5) (Ref. TASK 29-10-00-720-001).
(2)
Examine the hydraulic connections of the engine pump fire-valve (5) for leaks.
Subtask 29-13-52-864-052
G. Depressurize the Applicable Hydraulic System WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES
_______ ARE CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
(1) Depressurize the Yellow hydraulic system (Ref. TASK 29-10-00-864-001).
5. Close-up
________ Subtask 29-13-52-410-050
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panels 674AB, 674BB. Subtask 29-13-52-942-051
B.
Removal of Equipment
(1)
Remove the container.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 29-13-52-000-002
Removal of the Actuator - Engine Pump Fire-Valve (3046GD)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific access platform 3 m (9 ft. 10 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-00-00-910-002 Safety Procedures of the Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-13-52-991-001 Fig. 401 29-13-52-991-002 Fig. 402
3. Job Set-up
__________
(Ref. Fig. 401/TASK 29-13-52-991-001) Subtask 29-13-52-941-057
A. Safety Precautions
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
(1)
You must obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002) when you work on the hydraulic system.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓4(96)
